Makita BFT021F Instructions Manual

Also see for BFT020F: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

Makita BFT021F Instructions Manual Manual pdf 3 page image

3ENGLISHExplanation of general view1-1. Battery cartridge1-2. Button2-1. Red part2-2. Button2-3. Battery cartridge3-1. Switch trigger4-1. Reversing switch lever5-1. Front lamp6-1. LED indicator7-1. Adjusting ring7-2. Ring8-1. Adjusting ring8-2. Ring8-3. Scale8-4. Adjusting grip8-5. Hole for adjusting grip8-6. Yellow line8-7. Compression spring10-1. Bit10-2. Sleeve12-1. Limit mark13-1. Brush holder cap13-2. ScrewdriverSPECIFICATIONSModel BFT020F BFT021F BFT040F BFT080F BFT122F BFT042F BFT081F BFT123FHard joint 0.5 - 2 N•m 0.5 - 2 N•m 1 - 4 N•m 3 - 8 N•m 5 - 12 N•m 1 - 4 N•m 3 - 8 N•m 5 - 12 N•mFasteningtorque Soft joint 0.5 - 2 N•m 0.5 - 2 N•m 1 - 3.5 N•m 3 - 6.5 N•m 5 - 10 N•m 1 - 3.5 N•m 3 - 7.5 N•m 5 - 12 N•mNo load speed (min -1) 540 320 950 540 320 1,200 700 390200 x 65 x 251mm(with Battery Cartridge BH9020/BH9020A)200 x 71 x 242 mm(with Battery Cartridge BH1220C)Dimensions200 x 65 x 274 mm(with Battery Cartridge BH9033/BH9033A)200 x 71 x251 mm(with Battery Cartridge BH1233C)1.3 kg(with Battery Cartridge BH9020/BH9020A)1.5 kg(with Battery Cartridge BH1220C)Net weight1.5 kg(with Battery Cartridge BH9033/BH9033A)1.7 kg(with Battery Cartridge BH1233C)Rated voltage D.C.9.6V D.C.12V• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.• Note: Specifications may differ from country to country.ENE033-1Intended useThe tool is intended for screw driving in wood, metal andplastic. ENF002-1Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, andcan only be operated on single-phase AC supply. Theyare double-insulated in accordance with EuropeanStandard and can, therefore, also be used from socketswithout earth wire. ENG001-2For European countries onlyNoise and VibrationThe typical A-weighted sound pressure level is not morethan 70 dB (A).The noise level under working may exceed 85 dB (A).Wear ear protection.The typical weighted root mean square accelerationvalue is not more than 2.5 m/s2 .These values have been obtained according toEN60745. ENH102-5Model; BFT020F,BFT021F,BFT040F,BFT042F,BFT080F,BFT081F,BFT122F,BFT123FEC-DECLARATION OF CONFORMITYWe declare under our sole responsibility that thisproduct is in compliance with the following standards ofstandardized documents;EN60745, EN55014 in accordance with CouncilDirectives, 89/336/EEC, 98/37/EC.Yasuhiko Kanzaki CE2006000087DirectorMAKITA INTERNATIONAL EUROPE LTD.Michigan Drive, Tongwell, Milton Keynes, Bucks MK158JD, ENGLANDResponsible manufacturer:Makita Corporation Anjo Aichi Japan ENB026-1ADDITIONAL SAFETY RULESFOR TOOL1. Be aware that this tool is always in anoperating condition, because it does not haveto be plugged into an electrical outlet.2. Hold tool by insulated gripping surfaces whenperforming an operation where the cutting toolmay contact hidden wiring. Contact with a "live"wire will also make exposed metal parts of the tool"live" and shock the operator.