Makita BHR180 Instruction Manual

Also see for BHR202: Parts Breakdown Specifications Instruction manual Instruction manual Instruction manual

Contents

6loosen up the lubrication. Without proper warm-up, hammering operation is difficult.8. Always be sure you have a firm footing. Be sureno one is below when using the tool in highlocations.9. Hold the tool firmly with both hands.10. Keep hands away from moving parts.11. Do not leave the tool running. Operate the toolonly when hand-held.12. Do not point the tool at any one in the area whenoperating. The bit could fly out and injuresomeone seriously.13. Do not touch the bit or parts close to the bitimmediately after operation; they may beextremely hot and could burn your skin.14. Some material contains chemicals which may betoxic. Take caution to prevent dust inhalation andskin contact. Follow material supplier safety data.SAVE THESE INSTRUCTIONS.WARNING:MISUSE or failure to follow the safety rules stated inthis instruction manual may cause serious personalinjury.IMPORTANT SAFETYINSTRUCTIONS ENC007-2FOR BATTERY CARTRIDGE1. Before using battery cartridge, read allinstructions and cautionary markings on (1)battery charger, (2) battery, and (3) product usingbattery.2. Do not disassemble battery cartridge.3. If operating time has become excessively shorter,stop operating immediately. It may result in a riskof overheating, possible burns and even anexplosion.4. If electrolyte gets into your eyes, rinse them outwith clear water and seek medical attention rightaway. It may result in loss of your eyesight.5. Do not short the battery cartridge:(1) Do not touch the terminals with anyconductive material.(2) Avoid storing battery cartridge in a containerwith other metal objects such as nails, coins,etc.(3) Do not expose battery cartridge to water orrain.A battery short can cause a large current flow,overheating, possible burns and even abreakdown.6. Do not store the tool and battery cartridge inlocations where the temperature may reach orexceed 50°C (122°F).7. Do not incinerate the battery cartridge even if it isseverely damaged or is completely worn out. Thebattery cartridge can explode in a fire.8. Be careful not to drop or strike battery.SAVE THESE INSTRUCTIONS.Tips for maintaining maximum battery life1. Charge the battery cartridge before completelydischarged.Always stop tool operation and charge the batterycartridge when you notice less tool power.2. Never recharge a fully charged battery cartridge.Overcharging shortens the battery service life.3. Charge the battery cartridge with roomtemperature at 10°C - 40°C (50°F - 104°F). Let a hotbattery cartridge cool down before charging it.FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function on the tool.Installing or removing battery cartridge(Fig. 1)• Always switch off the tool before insertion or removal ofthe battery cartridge.• To remove the battery cartridge, withdraw it from thetool while sliding the button on the front of the cartridge.• To insert the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. Always insert it all the way until it locks inplace with a little click. If you can see the red part onthe upper side of the button, it is not locked completely.Insert it fully until the red part cannot be seen. If not, itmay accidentally fall out of the tool, causing injury toyou or someone around you.• Do not use force when inserting the battery cartridge. Ifthe cartridge does not slide in easily, it is not beinginserted correctly.Switch action (Fig. 2)CAUTION:• Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased.To start the tool, simply pull the switch trigger. Tool speedis increased by increasing pressure on the switch trigger.Release the switch trigger to stop.Lighting up the lamp (Fig. 3)CAUTION:• Do not look in the light or see the source of lightdirectly.Pull the switch trigger to light up the lamp. The lampkeeps on lighting while the switch trigger is being pulled.The light automatically goes out 10 - 15 seconds after theswitch trigger is released.NOTE:• Use a dry cloth to wipe the dirt off the lens of lamp. Becareful not to scratch the lens of lamp, or it may lowerthe illumination.• Do not use thinner or gasoline to clean the lamp. Suchsolvents may damage it.