Makita DHP487RAJ Instruction Manual

Also see for DHP487: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

5 ENGLISHVibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN62841-2-1:Work mode: impact drilling into concreteVibration emission (a h,ID ) : 10.5 m/s 2Uncertainty (K) : 1.5 m/s2Work mode: drilling into metalVibration emission (a h,D ) : 2.5 m/s 2 or lessUncertainty (K) : 1.5 m/s2NOTE: The declared vibration total value(s) has beenmeasured in accordance with a standard test methodand may be used for comparing one tool with another.NOTE: The declared vibration total value(s) may alsobe used in a preliminary assessment of exposure.WARNING: The vibration emission during actualuse of the power tool can differ from the declared val-ue(s) depending on the ways in which the tool is usedespecially what kind of workpiece is processed.WARNING: Be sure to identify safety measuresto protect the operator that are based on an estimationof exposure in the actual conditions of use (takingaccount of all parts of the operating cycle such as thetimes when the tool is switched off and when it is run-ning idle in addition to the trigger time).EC Declaration of ConformityFor European countries onlyThe EC declaration of conformity is included as Annex Ato this instruction manual.SAFETY WARNINGSGeneral power tool safety warningsWARNING: Read all safety warnings, instruc-tions, illustrations and specifications provided with thispower tool. Failure to follow all instructions listed belowmay result in electric shock, fire and/or serious injury.Save all warnings and instruc-tions for future reference.The term "power tool" in the warnings refers to your mains-oper-ated (corded) power tool or battery-operated (cordless) power tool.Cordless hammer driver drill safetywarningsSafety instructions for all operations1. Wear ear protectors when impact drilling.Exposure to noise can cause hearing loss.2. Hold the power tool by insulated gripping surfaces,when performing an operation where the cuttingaccessory or fasteners may contact hidden wiring.Cutting accessory or fasteners contacting a "live" wiremay make exposed metal parts of the power tool "live"and could give the operator an electric shock.3. Always be sure you have a firm footing. Besure no one is below when using the tool inhigh locations.4. Hold the tool firmly.5. Keep hands away from rotating parts.6. Do not leave the tool running. Operate the toolonly when hand-held.7. Do not touch the drill bit, the workpiece orchips immediately after operation; they may beextremely hot and could burn your skin.8. Some material contains chemicals which maybe toxic. Take caution to prevent dust inhala-tion and skin contact. Follow material suppliersafety data.9. If the drill bit cannot be loosened even youopen the jaws, use pliers to pull it out. In such acase, pulling out the drill bit by hand may result ininjury by its sharp edge.10. Make sure there are no electrical cables, waterpipes, gas pipes etc. that could cause a hazardif damaged by use of the tool.Safety instructions when using long drill bits1. Never operate at higher speed than the max-imum speed rating of the drill bit. At higherspeeds, the bit is likely to bend if allowed to rotatefreely without contacting the workpiece, resultingin personal injury.2. Always start drilling at low speed and with thebit tip in contact with the workpiece. At higherspeeds, the bit is likely to bend if allowed to rotatefreely without contacting the workpiece, resultingin personal injury.3. Apply pressure only in direct line with the bitand do not apply excessive pressure. Bits canbend causing breakage or loss of control, resultingin personal injury.SAVE THESE INSTRUCTIONS.WARNING: DO NOT let comfort or familiaritywith product (gained from repeated use) replacestrict adherence to safety rules for the subjectproduct. MISUSE or failure to follow the safetyrules stated in this instruction manual may causeserious personal injury.Important safety instructions forbattery cartridge1. Before using battery cartridge, read all instruc-tions and cautionary markings on (1) batterycharger, (2) battery, and (3) product usingbattery.2. Do not disassemble or tamper with the batterycartridge. It may result in a fire, excessive heat,or explosion.3. If operating time has become excessivelyshorter, stop operating immediately. It mayresult in a risk of overheating, possible burnsand even an explosion.4. If electrolyte gets into your eyes, rinse themout with clear water and seek medical atten-tion right away. It may result in loss of youreyesight.