Makita DLS714Z Instruction Manual

Also see for DLS714: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

12 ENGLISHNoiseThe typical A-weighted noise level determined accord-ing to EN61029:Sound pressure level (L pA ) : 88 dB(A)Sound power level (LWA ) : 97 dB (A)Uncertainty (K) : 3 dB(A)WARNING: Wear ear protection.VibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN61029:Vibration emission (a h) : 2.5 m/s2 or lessUncertainty (K) : 1.5 m/s2NOTE: The declared vibration emission value hasbeen measured in accordance with the standard testmethod and may be used for comparing one tool withanother.NOTE: The declared vibration emission valuemay also be used in a preliminary assessment ofexposure.WARNING: The vibration emission during actualuse of the power tool can differ from the declaredemission value depending on the ways in which thetool is used.WARNING: Be sure to identify safety measuresto protect the operator that are based on an estima-tion of exposure in the actual conditions of use (takingaccount of all parts of the operating cycle such asthe times when the tool is switched off and when it isrunning idle in addition to the trigger time).EC Declaration of ConformityFor European countries onlyMakita declares that the following Machine(s):Designation of Machine: Cordless Slide CompoundMiter SawModel No./ Type: DLS714Conforms to the following European Directives:2006/42/ECThey are manufactured in accordance with the followingstandard or standardized documents: EN61029The technical file in accordance with 2006/42/EC isavailable from:Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium16.1.2015Yasushi FukayaDirectorMakita, Jan-Baptist Vinkstraat 2, 3070, BelgiumGeneral power tool safety warningsWARNING: Read all safety warnings andall instructions. Failure to follow the warnings andinstructions may result in electric shock, fire and/orserious injury.Save all warnings and instruc-tions for future reference.The term "power tool" in the warnings refers to yourmains-operated (corded) power tool or battery-operated(cordless) power tool.Cordless miter saw safety warnings1. Keep hands out of path of saw blade. Avoidcontact with any coasting blade. It can stillcause severe injury.2. Check the saw blade carefully for cracks ordeformation before operation.Replace damaged blades immediately.3. Replace the kerf board when worn.4. Use only saw blades specified by the manufac-turer which conform to EN847-1.5. Do not use saw blades manufactured fromhigh speed steel.6. Wear eye protection.7. Wear hearing protection to reduce the risk ofhearing loss.8. Wear gloves for handling saw blade (sawblades shall be carried in a holder whereverpracticable) and rough material.9. Connect miter saws to a dust collecting devicewhen sawing.10. Select saw blades in relation to the material tobe cut.11. Always secure all moving portions before car-rying the tool. When lifting or carrying the tool,do not use the guard as a carrying handle.12. Do not operate saw without guards in place.Check blade guard for proper closing beforeeach use. Do not operate saw if blade guard doesnot move freely and close instantly. Never clampor tie the blade guard into the open position.13. Keep the floor area free of loose material e.g.chips and cut-offs.14. Use only saw blades that are marked with amaximum speed equal to or higher than the noload speed marked on the tool.15. When the tool is fitted with a laser or LED, donot replace the laser or LED with a differenttype. Ask an authorized service center for repair.16. Never remove any cut-offs or other parts of theworkpiece from the cutting area whilst the toolis running with an unguarded saw blade.17. Do not perform any operation freehand. Theworkpiece must be secured firmly against the turnbase and guide fence with the vise during all opera-tions. Never use your hand to secure the workpiece.18. Ensure that the tool is stable before each cut.19. Fix the tool to a work bench, if needed.20. Support long workpieces with appropriateadditional supports.21. Never cut so small workpiece which cannot besecurely held by the vise. Improperly held workpiecemay cause kickback and serious personal injury.22. Never reach around saw blade.23. Turn off tool and wait for saw blade to stopbefore moving workpiece or changingsettings.

/ 124

Related manuals for Makita DLS714

Makita DLS714 Instruction Manual

This manual is suitable for:

DLS714 DLS714NZ DLS714Z

manualsdatabase

Your AI-powered manual search engine