Makita DTW1001 Instruction Manual

Also see for DTW1001: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

battery life

Makita DTW1001 Instruction Manual Manual pdf 6 page image

6 ENGLISH10. The contained lithium-ion batteries are subjectto the Dangerous Goods Legislation require-ments.For commercial transports e.g. by third parties,forwarding agents, special requirement on pack-aging and labeling must be observed.For preparation of the item being shipped, consult-ing an expert for hazardous material is required.Please also observe possibly more detailednational regulations.Tape or mask off open contacts and pack up thebattery in such a manner that it cannot movearound in the packaging.11. Follow your local regulations relating to dis-posal of battery.SAVE THESE INSTRUCTIONS.CAUTION: Only use genuine Makita batteries.Use of non-genuine Makita batteries, or batteries thathave been altered, may result in the battery burstingcausing fires, personal injury and damage. It will alsovoid the Makita warranty for the Makita tool and charger.Tips for maintaining maximumbattery life1. Charge the battery cartridge before completely dis-charged. Always stop tool operation and charge thebattery cartridge when you notice less tool power.2. Never recharge a fully charged battery cartridge.Overcharging shortens the battery service life.3. Charge the battery cartridge with room tem-perature at 10 °C - 40 °C (50 °F - 104 °F). Leta hot battery cartridge cool down beforecharging it.4. Charge the battery cartridge if you do not useit for a long period (more than six months).FUNCTIONALDESCRIPTIONCAUTION: Always be sure that the tool isswitched off and the battery cartridge is removedbefore adjusting or checking function on the tool.Installing or removing batterycartridgeCAUTION: Always switch off the tool beforeinstalling or removing of the battery cartridge.CAUTION: Hold the tool and the battery car-tridge firmly when installing or removing batterycartridge. Failure to hold the tool and the batterycartridge firmly may cause them to slip off your handsand result in damage to the tool and battery cartridgeand a personal injury.► Fig.1: 1. Red indicator 2. Button 3. Battery cartridgeTo remove the battery cartridge, slide it from the toolwhile sliding the button on the front of the cartridge.To install the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. Insert it all the way until it locks in placewith a little click. If you can see the red indicator on theupper side of the button, it is not locked completely.CAUTION: Always install the battery cartridgefully until the red indicator cannot be seen. If not,it may accidentally fall out of the tool, causing injury toyou or someone around you.CAUTION: Do not install the battery cartridgeforcibly. If the cartridge does not slide in easily, it isnot being inserted correctly.Battery protection systemLithium-ion battery with star marking► Fig.2: 1. Star markingLithium-ion batteries with a star marking are equippedwith a protection system. This system automaticallycuts off power to the tool to extend battery life.The tool will automatically stop during operation if thetool and/or battery are placed under one of the followingconditions:Overloaded:The tool is operated in a manner that causes it to drawan abnormally high current.In this situation, turn the tool off and stop the applicationthat caused the tool to become overloaded. Then turnthe tool on to restart.If the tool does not start, the battery is overheated. Inthis situation, let the battery cool before turning the toolon again.Low battery voltage:The remaining battery capacity is too low and the toolwill not operate. In this situation, remove and rechargethe battery.Ташев-Галвинг ООДwww.tashev-galving.com

/ 96

Related manuals for Makita DTW1001

Makita DTW1001 Instruction Manual

This manual is suitable for:

DTW1001 DTW1002 DTW800

manualsdatabase

Your AI-powered manual search engine