Makita DUB142 Instruction Manual

Also see for BUB142: Instruction manual Instruction manual Instruction manual

Contents

Makita DUB142 Instruction Manual Manual pdf 5 page image

52. Never point the nozzle at anyone in the vicinitywhen using the blower.3. Warning - Electric shock could occur if used onwet surfaces. Do not expose to rain. Storeindoors.4. Never block suction inlet and/or blower outlet.• Do not block suction inlet or blower outlet toclean up in dusty areas.• Do not use the blower with a tapered nozzlesmaller than the original one, such as a newnozzle obtained by attaching an extra diameter-reduced hose or smaller hose to the nozzle topend.• Do not Use the blower to inflate balls, rubberboat or the similar.Increased motor revolution may cause dangerous fanbreakage and result in serious personal injury. Heatedmotor and control circuit may cause a fire.5. Keep children, other bystanders and pets awayfrom the blower while operating.6. Do not operate the blower near open window, etc.7. Operating the blower only at reasonable hours isrecommended - not early in the morning or late atnight when people might be disturbed.8. Using rakes and brooms to loosen debris beforeblowing is recommended.9. It is recommended to slightly dampen surfaces industy conditions or use mister attachmentavailable on the market.10. It is recommended to use the long nozzle so theair stream can work close to the ground.11. The blower is not intended for use by persons withreduced physical, sensory or mental capabilities,or lack of experience and knowledge.12. Young children should be supervised to ensurethat they do not play with the blower.13. Do not insert fingers or other objects into suctioninlet or blower outlet.14. Always use the dust bag when collecting dust,chips and the like.15. Do not collect still smoldering cigarette ashes,freshly cut metals shavings, screws, nails and thelike.SAVE THESE INSTRUCTIONS.WARNING:DO NOT let comfort or familiarity with product (gainedfrom repeated use) replace strict adherence to safetyrules for the subject product. MISUSE or failure tofollow the safety rules stated in this instructionmanual may cause serious personal injury.IMPORTANT SAFETYINSTRUCTIONS ENC007-7FOR BATTERY CARTRIDGE1. Before using battery cartridge, read allinstructions and cautionary markings on (1)battery charger, (2) battery, and (3) product usingbattery.2. Do not disassemble battery cartridge.3. If operating time has become excessively shorter,stop operating immediately. It may result in a riskof overheating, possible burns and even anexplosion.4. If electrolyte gets into your eyes, rinse them outwith clear water and seek medical attention rightaway. It may result in loss of your eyesight.5. Do not short the battery cartridge:(1) Do not touch the terminals with anyconductive material.(2) Avoid storing battery cartridge in a containerwith other metal objects such as nails, coins,etc.(3) Do not expose battery cartridge to water orrain.A battery short can cause a large current flow,overheating, possible burns and even abreakdown.6. Do not store the tool and battery cartridge inlocations where the temperature may reach orexceed 50°C (122°F).7. Do not incinerate the battery cartridge even if it isseverely damaged or is completely worn out. Thebattery cartridge can explode in a fire.8. Be careful not to drop or strike battery.9. Do not use a damaged battery.SAVE THESE INSTRUCTIONS.Tips for maintaining maximum battery life1. Charge the battery cartridge before completelydischarged.Always stop tool operation and charge the batterycartridge when you notice less tool power.2. Never recharge a fully charged battery cartridge.Overcharging shortens the battery service life.3. Charge the battery cartridge with roomtemperature at 10°C - 40°C (50°F - 104°F). Let a hotbattery cartridge cool down before charging it.4. Charge the battery cartridge once in every sixmonths if you do not use it for a long period oftime.FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function on the tool.Installing or removing battery cartridge(Fig. 1)• Always switch off the tool before insertion or removal ofthe battery cartridge.• To remove the battery cartridge, withdraw it from thetool while pressing the buttons on both sides of thecartridge.• To insert the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. Always insert it all the way until it locks inplace with a little click. If not, it may accidentally fall outof the tool, causing injury to you or someone aroundyou.