Makita DUM166 Instruction Manual

Also see for DUM166: Instruction manual Technical information Instruction manual Instruction manual Instruction manual

Contents

Makita DUM166 Instruction Manual Manual pdf 12 page image

12ENC007-9IMPORTANT SAFETYINSTRUCTIONSFOR BATTERY CARTRIDGE1. Before using battery cartridge, read allinstructions and cautionary markings on (1)battery charger, (2) battery, and (3) productusing battery.2. Do not disassemble battery cartridge.3. If operating time has become excessivelyshorter, stop operating immediately. It mayresult in a risk of overheating, possible burnsand even an explosion.4. If electrolyte gets into your eyes, rinse themout with clear water and seek medicalattention right away. It may result in loss ofyour eyesight.5. Do not short the battery cartridge:(1) Do not touch the terminals with anyconductive material.(2) Avoid storing battery cartridge in acontainer with other metal objects such asnails, coins, etc.(3) Do not expose battery cartridge to wateror rain.A battery short can cause a large current flow,overheating, possible burns and even abreakdown.6. Do not store the tool and battery cartridge inlocations where the temperature may reach orexceed 50 ﾟ C (122 ﾟ F).7. Do not incinerate the battery cartridge even ifit is severely damaged or is completely wornout. The battery cartridge can explode in a fire.8. Be careful not to drop or strike battery.9. Do not use a damaged battery.10. Follow your local regulations relating todisposal of battery.SAVE THESE INSTRUCTIONS.Tips for maintaining maximum battery life1. Charge the battery cartridge beforecompletely discharged.Always stop tool operation and charge thebattery cartridge when you notice less toolpower.2. Never recharge a fully charged batterycartridge.Overcharging shortens the battery service life.3. Charge the battery cartridge with roomtemperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).Let a hot battery cartridge cool down beforecharging it.4. Charge the battery cartridge if you do not useit for a long period (more than six months).FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function on the tool.Installing or removing battery cartridgeFig.1CAUTION:• Always switch off the tool before installing orremoving of the battery cartridge.• Hold the tool and the battery cartridge firmly wheninstalling or removing battery cartridge. Failure tohold the tool and the battery cartridge firmly may causethem to slip off your hands and result in damage to thetool and battery cartridge and a personal injury.To remove the battery cartridge, slide it from the toolwhile sliding the button on the front of the cartridge.To install the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. Insert it all the way until it locks in place witha little click. If you can see the red indicator on the upperside of the button, it is not locked completely.CAUTION:• Always install the battery cartridge fully until thered indicator cannot be seen. If not, it mayaccidentally fall out of the tool, causing injury toyou or someone around you.• Do not install the battery cartridge forcibly. If thecartridge does not slide in easily, it is not beinginserted correctly.Battery protection system(Lithium-ion battery with star marking)Fig.2Lithium-ion batteries with a star marking are equippedwith a protection system. This system automatically cutsoff power to the tool to extend battery life.The tool will automatically stop during operation if thetool and/or battery are placed under one of the followingconditions:• Overloaded:The tool is operated in a manner that causesit to draw an abnormally high current.In this situation, release the trigger switch onthe tool and stop the application that causedthe tool to become overloaded. Then pull thetrigger switch again to restart.If the tool does not start, the battery isoverheated. In this situation, let the batterycool before pulling the trigger switch again.• Low battery voltage:The remaining battery capacity is too low andthe tool will not operate. In this situation,remove and recharge the battery.