Makita HM1317C Instruction Manual

Also see for HM1307C: Instruction manual Instruction manual Instruction manual Instruction mamual Instruction manual

Contents

Makita HM1317C Instruction Manual Manual pdf 4 page image

4ENGLISH (Original instructions)Explanation of general viewSPECIFICATIONS• Due to our continuing programme of research and development, the specifications herein are subject to change withoutnotice.• Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003Intended use ENE045-1The tool is intended for chiselling work in concrete, brick,stone and asphalt as well as for driving and compactingwith appropriate accessories.Power supply ENF002-1The tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, and canonly be operated on single-phase AC supply. They aredouble-insulated in accordance with European Standardand can, therefore, also be used from sockets withoutearth wire.General Power Tool SafetyWarnings GEA010-1WARNING Read all safety warnings and allinstructions. Failure to follow the warnings andinstructions may result in electric shock, fire and/orserious injury.Save all warnings andinstructions for future reference.HAMMER SAFETY WARNINGSGEB004-61. Wear ear protectors. Exposure to noise can causehearing loss.2. Use auxiliary handle(s), if supplied with the tool.Loss of control can cause personal injury.3. Hold power tool by insulated gripping surfaces,when performing an operation where the cuttingaccessory may contact hidden wiring or its owncord. Cutting accessory contacting a “live” wire maymake exposed metal parts of the power tool “live” andcould give the operator an electric shock.4. Wear a hard hat (safety helmet), safety glassesand/or face shield. Ordinary eye or sun glassesare NOT safety glasses. It is also highlyrecommended that you wear a dust mask andthickly padded gloves.5. Be sure the bit is secured in place beforeoperation.6. Under normal operation, the tool is designed toproduce vibration. The screws can come looseeasily, causing a breakdown or accident. Checktightness of screws carefully before operation.7. In cold weather or when the tool has not beenused for a long time, let the tool warm up for awhile by operating it under no load. This willloosen up the lubrication. Without proper warm-up, hammering operation is difficult.8. Always be sure you have a firm footing. Be sureno one is below when using the tool in highlocations.9. Hold the tool firmly with both hands.10. Keep hands away from moving parts.11. Do not leave the tool running. Operate the toolonly when hand-held.12. Do not point the tool at any one in the area whenoperating. The bit could fly out and injuresomeone seriously.13. Do not touch the bit or parts close to the bitimmediately after operation; they may beextremely hot and could burn your skin.14. Do not operate the tool at no-load unnecessarily.15. Some material contains chemicals which may betoxic. Take caution to prevent dust inhalation andskin contact. Follow material supplier safety data.1. Switch lever2. Adjusting dial3. Power-ON indicator lamp (green)4. Service indicator lamp (red)5. Set bolt6. Nut7. Side handle8. Bit9. Tool retainer10. Tool holder11. Bit with collar12. Bit without collar13. When the bit is inserted14. When the bit is retained15. Rear cover16. Hex wrench17. Crank cap18. Hammer grease19. Crank cap coverModel HM1317C HM1307C HM1317CB HM1307CBBlows per minute 730 - 1,450Overall length 715 mm 824 mmNet weight 17.0 kg 15.3 kg 19.0 kg 17.3 kgSafety class /II

/ 44

Related manuals for Makita HM1307C

Makita HM1317C Instruction Manual

This manual is suitable for:

HM1307C HM1307CB HM1317C HM1317CB

manualsdatabase

Your AI-powered manual search engine