Makita HM1801 Manual

Also see for HM1810: Parts Breakdown Instruction manual Parts Breakdown Instruction manual Instruction manual

Contents

Makita HM1801 Manual Manual pdf 5 page image

5GEB004-6HAMMER SAFETY WARNINGS1. Wear ear protectors. Exposure to noise cancause hearing loss.2. Use auxiliary handle(s), if supplied with thetool. Loss of control can cause personal injury.3. Hold power tool by insulated grippingsurfaces, when performing an operation wherethe cutting accessory may contact hiddenwiring or its own cord. Cutting accessorycontacting a "live" wire may make exposed metalparts of the power tool "live" and could give theoperator an electric shock.4. Wear a hard hat (safety helmet), safety glassesand/or face shield. Ordinary eye or sunglasses are NOT safety glasses. It is alsohighly recommended that you wear a dustmask and thickly padded gloves.5. Be sure the bit is secured in place beforeoperation.6. Under normal operation, the tool is designedto produce vibration. The screws can comeloose easily, causing a breakdown or accident.Check tightness of screws carefully beforeoperation.7. In cold weather or when the tool has not beenused for a long time, let the tool warm up for awhile by operating it under no load. This willloosen up the lubrication. Without properwarm-up, hammering operation is difficult.8. Always be sure you have a firm footing.Be sure no one is below when using the tool inhigh locations.9. Hold the tool firmly with both hands.10. Keep hands away from moving parts.11. Do not leave the tool running. Operate the toolonly when hand-held.12. Do not point the tool at any one in the areawhen operating. The bit could fly out andinjure someone seriously.13. Do not touch the bit or parts close to the bitimmediately after operation; they may beextremely hot and could burn your skin.14. Do not operate the tool at no-loadunnecessarily.15. Some material contains chemicals which maybe toxic. Take caution to prevent dustinhalation and skin contact. Follow materialsupplier safety data.SAVE THESE INSTRUCTIONS.WARNING:DO NOT let comfort or familiarity with product(gained from repeated use) replace strict adherenceto safety rules for the subject product.MISUSE or failure to follow the safety rules stated inthis instruction manual may cause serious personalinjury.FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off andunplugged before adjusting or checking function onthe tool.Switch actionFig.1CAUTION:• Before plugging in the tool, always check to seethat the switch lever actuates properly and returnsto the "OFF" position when released.To start the tool, simply squeeze the switch lever.Release the switch lever to stop.Indicator lampFig.2The green power-ON indicator lamp lights up when thetool is plugged to the mains. If the indicator lamp is lit butthe tool does not start even if the tool is switched ON,the carbon brushes may be worn out, or the motor or theswitch may be defective. If the indicator lamp does notlight up, the mains cord or the indicator lamp may bedefective.ASSEMBLYCAUTION:• Always be sure that the tool is switched off andunplugged before carrying out any work on thetool.Installing or removing the bitFig.3This tool accepts bits either with or without a collar on itsshank.To install the bit, follow either procedure (1) or (2)described below.(1) For bits with a collarFig.4Pivot the tool retainer back and slightly downward.Insert the bit into the tool holder as far as it will go.To securely retain the bit, return the tool retainer toits original position.CAUTION:• Always assure that the bit is securely retained byattempting to pull the bit out of the tool holder aftercompleting the above procedure.(2) For bits without a collarFig.5Pivot the tool retainer front and slightly downward.With the notched portion of the bit facing the tool

/ 40

Related manuals for Makita HM1810

Makita HM1810 Manual

Makita HM1801 Instruction Manual

This manual is suitable for:

HM1810 HM1801

manualsdatabase

Your AI-powered manual search engine