Makita JS1600 Instruction Manual
Also see for JS1600: Instruction manualInstruction manualTechnical informationInstruction manualInstruction manual
                                    | |
3ENGLISH (Original instructions)Explanation of general view1-1. Lock-off lever in the FREE position1-2. Switch lever (Paddle switch)2-1. Lock-off lever in the LOCK position3-1. Lock-off lever3-2. Switch lever4-1. Gauge for stainless: 1.2 mm (3/64")4-2. Gauge for mild steel: 1.6 mm (1/16")5-1. Lower blade5-2. Loosen5-3. Upper blade5-4. Upper blade securing bolt5-5. Hex wrench6-1. Thin washers6-2. Blade holder6-3. Upper blade6-4. Upper blade securing bolt7-1. Tighten7-2. Upper blade securing bolt7-3. Upper blade8-1. Blade holder8-2. Upper blade securing bolt8-3. Upper blade8-4. No gap allowed9-1. Lower blade9-2. Tighten9-3. Yoke10-1. Yoke10-2. Lower blade positioning screw10-3. Lower blade11-1. Workholder13-1. Cutting line14-1. Limit mark15-1. Screwdriver15-2. Brush holder capSPECIFICATIONSModel JS1600Steel up to 400 N/mm 2 1.6 mm (16 ga.)Steel up to 600 N/mm 2 1.2 mm (18 ga.)Steel up to 800 N/mm 2 0.8 mm (22 ga.)Max. cutting capacitiesAluminum up to 200 N/mm 2 2.5 mm (13 ga.)Min. cutting radius 30 mmStrokes per minute (min -1) 4,000Overall length 230 mmNet weight 1.8 kgSafety class /II• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.• Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003ENE037-1Intended useThe tool is intended for cutting sheet steel and stainlesssheet steel. ENF002-1Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, and canonly be operated on single-phase AC supply. They aredouble-insulated in accordance with European Standardand can, therefore, also be used from sockets withoutearth wire. ENG104-2NoiseThe typical A-weighted noise level determined accordingto EN60745:Sound pressure level (LpA) : 78 dB(A)Uncertainty (K) : 3 dB(A)The noise level under working may exceed 80 dB (A).Wear ear protection. ENG218-2VibrationThe vibration total value (tri-axial vector sum) determinedaccording to EN60745:Work mode : cutting sheet metalVibration emission (ah ) : 6.5 m/s 2Uncertainty (K) : 1.5 m/s 2ENG901-1• The declared vibration emission value has beenmeasured in accordance with the standard testmethod and may be used for comparing one toolwith another.• The declared vibration emission value may also beused in a preliminary assessment of exposure.WARNING:• The vibration emission during actual use of thepower tool can differ from the declared emissionvalue depending on the ways in which the tool isused.• Be sure to identify safety measures to protect theoperator that are based on an estimation ofexposure in the actual conditions of use (takingaccount of all parts of the operating cycle such asthe times when the tool is switched off and when itis running idle in addition to the trigger time). |
Related manuals for Makita JS1600
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1600 Instruction Manual
Makita JS1602 Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine