Makita KP0810 Instruction Manual

Also see for KP0810: Instruction manual Parts Breakdown Instruction manual Instruction manual Instruction manual

Contents

8installation bolts with the socket wrench. The drumcover comes off together with the blades. (Fig. 7)2. To install the blades, loosely attach the adjusting plateto the set plate with the pan head screws and set themini planer blade on the gauge base so that thecutting edge of the blade is perfectly flush with theinside flank of the gauge plate. (Fig. 8)3. Set the adjusting plate/set plate on the gauge base sothat the planer blade locating lugs on the set plate restin the mini planer blade groove, then press in the heelof the adjusting plate flush with the back side of thegauge base and tighten the pan head screws.4. It is important that the blade sits flush with the insideflank of the gauge plate, the planer blade locating lugssit in the blade groove and the heel of the adjustingplate is flush with the back side of the gauge base.Check this alignment carefully to ensure uniformcutting.5. Slip the heel of the adjusting plate into the groove ofthe drum.6. Set the drum cover over the adjusting plate/set plateand screw in the three hex flange head bolts so that agap exists between the drum and the set plate to slidethe mini planer blade into position. The blade will bepositioned by the planer blade locating lugs on the setplate. (Fig. 9)7. The blade’s lengthwise adjustment will need to bemanually positioned so that the blade ends are clearand equidistant from the housing on one side and themetal bracket on the other.8. Tighten the three hex flange head bolts (with thesocket wrench provided) and rotate the drum to checkclearances between the blade ends and the tool body.9. Check the three hex flange head bolts for finaltightness.10. Repeat procedures 1 - 9 for other blade.For the correct planer blade settingYour planing surface will end up rough and uneven,unless the blade is set properly and securely. The blademust be mounted so that the cutting edge is absolutelylevel, that is, parallel to the surface of the rear base.Refer to some examples below for proper and impropersettings.(A) Front base (Movable shoe)(B) Rear base (Stationary shoe)EN0004-1Change of chip discharge direction(Fig. 10)Chip discharge direction can be changed to the right orleft. To change the direction, pull out the stopper whileturning it slightly backward and fit in it in one of twoopenings on the opposite side of chip discharge so thatthe recessed part fits to protrusion. (Fig. 11)Dust bag (accessory) (Fig. 12)Attach the dust bag onto the chip discharge opening.The chip discharge opening is tapered. When attachingthe dust bag, push it onto the chip discharge openingfirmly as far as it will go to prevent it from coming offduring operation.When the dust bag is about half full, remove the dust bagfrom the tool and pull the fastener out. Empty the dust bagof its contents, tapping it lightly so as to remove particlesadhering to the insides which might hamper furthercollection. (Fig. 13)NOTE:• If you connect a Makita vacuum cleaner to this tool,more efficient and cleaner operations can beperformed.Connecting a vacuum cleaner (Fig. 14)When you wish to perform clean planing operation,connect a Makita vacuum cleaner to your tool. Thenconnect a hose of the vacuum cleaner to the chipdischarge opening as shown in the figures.Correct setting Although this side view cannot show it, theedges of the blades run perfectly parallel tothe rear base surface.Nicks in surface Cause: One or both blades fails to have edgeparallel to rear base line.Gouging at start Cause: One or both blade edges fails toprotrude enough in relation to rearbase line.Gouging at end Cause: One or both blade edges protrudestoo far in relation to rear base line.(A) (B)(B)(A)(A) (B)

/ 60

Related manuals for Makita KP0810

Makita KP0810 Instruction Manual

Makita KP0810C Instruction Manual

This manual is suitable for:

KP0810 KP0810C

manualsdatabase

Your AI-powered manual search engine