Makita LS1018 Instruction Manual
Also see for LS1018: Instruction manualInstruction manualInstruction manualInstruction manualInstruction manual
                                                                                                                                | |
Contents
| 
8SPECIFICATIONSModel LS1018 / LS1018LBlade diameter 255 mm - 260 mmHole diameterFor all countries other than European countries 25.4 mmFor European countries 30 mmMax. Cutting capacities (H x W) with 260 mm in diameterBevel angleMiter angle 45° (left) 0° 45° (right)0° 50 mm x 310 mm 91 mm x 310 mm 31 mm x 310 mm45° 50 mm x 220 mm 91 mm x 220 mm 31 mm x 220 mm60° (right) - 91 mm x 153 mm -No load speed (min -1) 4,300Laser Type (LS1018L only) Red Laser 650 nm, 1mW ( Laser Class 2 )Dimensions (L x W x H) 825 mm x 536 mm x 633 mmNet weight For all countries other than European countries………19.8 kgFor European countries…………………………………….…19.9 kgSafety class /II• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.• Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003END222-1SymbolsThe following show the symbols used for the equipment.Be sure that you understand their meaning before use.･ Read instruction manual.･ DOUBLE INSULATION･ To avoid injury from flying debris, keepholding the saw head down, aftermaking cuts, until the blade has cometo a complete stop.･ When performing slide cut, first pullcarriage fully and press down handle,then push carriage toward the guidefence.･ Do not place hand or fingers close tothe blade.･ Adjust sliding fences clear of blade andblade guard properly.･ Always remove SUB-FENCE R whenperforming right bevel cuts. Failure to doso may cause serious injury to operator.･ Never look into the laser beam. Directlaser beam may injure your eyes.･ Only for EU countriesDo not dispose of electric equipmenttogether with household waste material!In observance of European Directive2002/96/EC on waste electric andelectronic equipment and itsimplementation in accordance withnational law, electric equipment thathave reached the end of their life mustbe collected separately and returned toan environmentally compatiblerecycling facility. ENE006-1Intended useThe tool is intended for accurate straight and mitercutting in wood. With appropriate saw blades, aluminumcan also be sawed. ENF002-1Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, andcan only be operated on single-phase AC supply. Theyare double-insulated in accordance with EuropeanStandard and can, therefore, also be used from socketswithout earth wire. ENG905-1NoiseThe typical A-weighted noise level determined accordingto EN61029:Sound pressure level (LpA) : 97 dB(A)Sound power level (LWA) : 103 dB(A)Uncertainty (K) : 3 dB(A)Wear ear protectionENG900-1VibrationThe vibration total value (tri-axial vector sum)determined according to EN61029: |
Related manuals for Makita LS1018
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
Makita LS1018 Instruction Manual
manualsdatabase
Your AI-powered manual search engine