Makita RP0910 Instruction Manual

Also see for RP0910: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

safety instructions

Makita RP0910 Instruction Manual Manual pdf 6 page image

6ENGLISHExplanation of general view1 Collet nut2 Wrench3 Shaft lock4 Tighten5 Loosen6 Correct size collet cone7 Stopper pole8 Depth pointer9 Lock knob10 Fast-feed button11 Adjusting hex bolt12 Adjusting knob13 Stopper block14 Nylon nut15 Hex nut16 Lock button17 Switch trigger18 Speed adjusting dial19 Workpiece20 Bit revolving direction21 Feed direction22 (View from the top of thetool)23 Correct bit feed direction24 Lock screw25 Guiding surface26 Straight guide27 Templet guide28 Screw29 Bit30 Base31 Templet32 Workpiece33 Templet guide34 Nozzle assembly35 Dust nozzle assembly36 Limit mark37 Brush holder cap38 Screwdriver39 Stopper pole setting nutSPECIFICATIONSModel RP0910 RP1110CMax. collet capacity ..................................................................... ø8 mm ø8 mmPlunge capacity ........................................................................... 0 – 57 mm 0 – 57 mmNo load speed (min–1) ................................................................. 27,000 8,000 – 24,000Overall height .............................................................................. 260 mm 260 mmNet weight ................................................................................... 3.3 kg 3.4 kg• Due to our continuing program of research and devel-opment, the specifications herein are subject to changewithout notice.• Note: Specifications may differ from country to country.Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, and canonly be operated on single-phase AC supply. They aredouble-insulated in accordance with European Standardand can, therefore, also be used from sockets withoutearth wire.SAFETY INSTRUCTIONSWarning! When using electric tools, basic safety pre-cautions should always be followed to reduce therisk of fire, electric shock and personal injury, includ-ing the following. Read all these instructions beforeattempting to operate this product and save theseinstructions.For safe operation:1. Keep work area cleanCluttered areas and benches invite injuries.2. Consider work area environmentDon’t expose power tools to rain. Don’t use powertools in damp or wet locations. Keep work area welllit. Don’t use power tools in presence of flammableliquids or gases.3. Guard against electric shockPrevent body contact with grounded surfaces (e.g.pipes, radiators, ranges, refrigerators).4. Keep children awayDo not let visitors contact tool or extension cord. Allvisitors should be kept away from work area.5. Store idle toolsWhen not in use, tools should be stored in dry, high,or locked-up place, out of the reach of children.6. Don’t force toolIt will do the job better and safer at the rate for whichit was intended.7. Use right toolDon’t force small tools or attachments to do the jobof a heavy duty tool. Don’t use tools for purposes notintended; for example, don’t use circular saw for cut-ting tree limbs or logs.8. Dress properlyDo not wear loose clothing or jewelry. They can becaught in moving parts. Rubber gloves and non-skidfootwear are recommended when working outdoors.Wear protective hair covering to contain long hair.9. Use safety glasses and hearing protectionAlso use face or dust mask if cutting operation isdusty.10. Connect dust extraction equipmentIf devices are provided for the connection of dustextraction and collection facilities, ensure these areconnected and properly used.11. Don’t abuse cordNever carry tool by cord or yank it to disconnect itfrom receptacle. Keep cord from heat, oil and sharpedges.12. Secure workUse clamps or a vise to hold work. It’s safer thanusing your hand and it frees both hands to operatetool.13. Don’t overreachKeep proper footing and balance at all times.14. Maintain tools with careKeep tools sharp and clean for better and safer per-formance. Follow instructions for lubricating andchanging accessories. Inspect tool cords periodi-cally and, if damaged, have repaired by authorizedservice facility. Inspect extension cords periodicallyand replace if damaged. Keep handles dry, cleanand free from oil and grease.

/ 24

Related manuals for Makita RP0910

Makita RP0910 Instruction Manual

Makita RP0900 Instruction Manual

This manual is suitable for:

RP0910 RP1110C

manualsdatabase

Your AI-powered manual search engine