Makita RP0910 Instruction Manual

Also see for RP0910: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

Makita RP0910 Instruction Manual Manual pdf 6 page image

ENGLISH Explanation of general view1 Collet nut2 Wrench3 Shaft lock4 Tighten5 Loosen6 Correct size collet cone7 Stopper pole8 Depth pointer9 Lock knob0 Fast-feed buttonq Adjusting hex boltw Adjusting knobe Stopper blockr Nylon nutt Hex nuty Lock buttonu Switch triggeri Speed adjusting dialo Workpiecep Bit revolving directiona Feed directions (View from the top of thetool)d Correct bit feed directionf Lock screwg Guiding surfaceh Straight guidej Templet guidek Screwl Bit; Basez Templetx Workpiecec Templet guidev Nozzle assemblyb Dust nozzle assemblyn Limit markm Brush holder cap, ScrewdriverSPECIFICATIONSModel RP0910 RP1110CMax. collet capacity .................................................... ø8 mm ø8 mmPlunge capacity .......................................................... 0 – 57 mm 0 – 57 mmNo load speed (min –1) ................................................ 27,000 8,000 – 24,000Overall height ............................................................. 260 mm 260 mmNet weight ................................................................... 3.3 kg 3.4 kg• Due to our continuing program of research anddevelopment, the specifications herein are subjectto change without notice.• Note: Specifications may differ from country tocountry.Power supplyThe tool should be connected only to a power supplyof the same voltage as indicated on the nameplate,and can only be operated on single-phase AC supply.They are double-insulated in accordance with Euro-pean Standard and can, therefore, also be used fromsockets without earth wire.Safety hintsFor your own safety, please refer to the enclosedsafety instructions.ADDITIONAL SAFETY RULES ENB033-11. Hold tool by insulated gripping surfaces whenperforming an operation where the cutting toolmay contact hidden wiring or its own cord.Contact with a ‘‘live’’ wire will make exposedmetal parts of the tool ‘‘live’’ and shock theoperator.2. Wear hearing protection during extendedperiod of operation.3. Handle the bits very carefully.4. Check the bit carefully for cracks or damagebefore operation. Replace cracked or dam-aged bit immediately.5. Avoid cutting nails. Inspect for and remove allnails from the workpiece before operation.6. Hold the tool firmly with both hands.7. Keep hands away from rotating parts.8. Make sure the bit is not contacting the work-piece before the switch is turned on.9. Before using the tool on an actual workpiece,let it run for a while. Watch for vibration orwobbling that could indicate improperlyinstalled bit.10. Be careful of the bit rotating direction and thefeed direction.11. Do not leave the tool running. Operate the toolonly when hand-held.12. Always switch off and wait for the bit to cometo a complete stop before removing the toolfrom workpiece.13. Do not touch the bit immediately after opera-tion; it may be extremely hot and could burnyour skin.14. Always lead the power supply cord away fromthe tool towards the rear.SAVE THESE INSTRUCTIONS.OPERATING INSTRUCTIONSInstalling or removing router bitImportant:Always be sure that the tool is switched off andunplugged before installing or removing the bit.Loosen the collet nut. Insert the bit all the way into thecollet cone. Press the shaft lock to keep the shaftstationary and use the wrench to tighten the collet nutsecurely. (Fig. 1)A 8 mm or 1/4’’ collet cone is factory installed on thetool. When using router bits with other shank diam-eter, use the correct size collet cone for the bit whichyou intended to use. (Fig. 2)Optional accessories include 6 mm, 8 mm and 1/4″collet cones.6

/ 64

Related manuals for Makita RP0910

Makita RP0910 Instruction Manual

Makita RP0900 Instruction Manual

This manual is suitable for:

RP0910 RP1110C

manualsdatabase

Your AI-powered manual search engine