Makita UH4570 Instruction Manual

Also see for UH4570: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

7specifications given on the identification plate. Werecommend the use of aresidual-current-operated circuit breaker(ground-fault circuit interrupter) with a trippingcurrent of 30 mA or less, or an earth leakagecurrent protector.11. Work gloves of stout leather are part of the basicequipment of the hedge trimmer and must alwaysbe worn when working with it. Also wear sturdyshoes with anti-skid soles.12. Before starting work check to make sure that thetrimmer is in good and safe working order. Ensureguards are fitted properly. Check cable fordamage before starting work and replace ifnecessary. The hedge trimmer must not be usedunless fully assembled.13. Keep cable away from the cutting area. Alwayswork in such a way that the extension power cordis behind you.14. Remove plug from the mains immediately if cableis damaged or cut.15. Make sure you have a secure footing beforestarting operation.16. Hold the tool firmly when using the tool.17. Do not operate the tool at no-load unnecessarily.18. Immediately switch off the motor and unplug themains plug if the cutter should come into contactwith a fence or other hard object. Check the cutterfor damage, and if damaged repair immediately.19. Before checking the cutter, taking care of faults, orremoving material caught in the cutter, alwaysswitch off the trimmer and unplug the mains plug.20. Switch off the trimmer and disconnect and securethe mains plug before doing any maintenancework.21. When moving the hedge trimmer to anotherlocation, including during work, always unplug themains plug. Never carry or transport the trimmerwith the cutter running. Never grasp the cutterwith your hands.22. Clean the hedge trimmer and especially the cutterafter use, and before putting the trimmer intostorage for extended periods. Lightly oil the cutterand put on the cover. The cover supplied with theunit can be hung on the wall, providing a safe andpractical way to store the hedge trimmer.23. Store the hedge trimmer with the cover on, in adry room. Keep it out of reach of children. Neverstore the trimmer outdoors.SAVE THESE INSTRUCTIONS.WARNING:DO NOT let comfort or familiarity with product(gained from repeated use) replace strict adherenceto safety rules for the subject product. MISUSE orfailure to follow the safety rules stated in thisinstruction manual may cause serious personalinjury.FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off andunplugged before adjusting or checking function onthe tool.Switch actionFig.1For your safety, this tool is equipped with a tripleswitching system. To turn on the tool, press two out ofthree triggers A, B and C. Release either one of the twopressed triggers to turn off. The sequence of switching isunimportant as the tool only starts when both switchesare activated.Straight cutFig.2To trim the hedge straight, pull triggers A and B.Vertical cutFig.3Cut upwards with both hands pull the switch triggers Band C and move it in front of your body.Far area cutFig.4To trim the hedge in far area with both hands pull theswitch triggers A and C.ASSEMBLYCAUTION:• Always be sure that the tool is switched off andunplugged before carrying out any work on thetool.Engage the extension cordCAUTION:• Make sure that the extension cord is unplugged tothe mains outlet.Fig.5When engaging the extension cord, secure it to the tool'scord with the hook complete. Attach the hook about 100- 200 mm from the extension cord connector. This willhelp prevent unintentional disconnection.Waist cord hookCAUTION:• Do not attach the holder of waist cord hook to otherthan the extension cord. Do not attach it in aposition closer to the tool beyond the hookcomplete. Failure to do so may cause an accidentor personal injury.• Attach firmly one hook of the hook complete to thetool's cord and the other hook of hook complete tothe extension cord. Working with the tool with a