MuxLab 500755 Quick Installation Manual
Also see for 500755: Quick setup guide
  | |
Contents | 
© MuxLab Inc. 94-000822-A SE-000822-A8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: videoease@muxlab.com URL: www.muxlab.comSpecificationsEnvironment 2CH Analog AudioDevices 2CH audio equipment, amplifiers, powered speakers, PA systems, AV camerasand players.Transmission Transparent to the user.Bandwidth 20Hz to 20KHzSignals 2CH analog audio ( in or out )SPDIF Out (2CH digital audio)ConnectorsNote: Cables not included.One (1) RCA receptacle for SPDIF out.One (1) 3.5mm jack for analog audio (in or out).One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.One (1) 3.5mm jack for IR Emitter or IR Sensor.One (1) DB9 Serial Port for RS232.Four (4) DIP Switches for device ID addressing and Transmitter/Receiver setting.Maximum DistanceExcluding 3.5mm cablelength.Cat5e/6: 330 ft (100 m)Note: When installed in an electrically noisy environment, an STP cable must beused. Also, cross-connections in the signal path reduce the effective distancedepending on the grade of twisted cable used.Latency 30msNetwork Requirement 100BaseT for Point to Point; 1000BaseT for other configuration.IR Frequency 38KHz to 58KHzRJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Cable One (1) Cat 5e/6 or better twisted pair cables required.Power Source This device supports PoE (PD), an external power supply is not included. It isintended to be powered via a PoE (PSE) Ethernet Switch. If required, an optionalpower supply (500993) may be purchased separately.PoE Standard IEEE 802.3afPower Consumption Transmitter: 2.9W Receiver: 1.8WTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingEnclosure Type Metal enclosure.Dimensions 3.70” x 3.68” x 0.97” (94 x 93.5 x 24.6 mm)Weight 1.1lbs (0.5kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 2 yearsOrder Information 500755 AUDIO / RS232 over IP PoE Transceiver500755-2PK AUDIO / RS232 over IP PoE Transceiver Kit(2PK kit includes two 500755 units)Accessories(These items are soldseparately)500905 3-Port Rackmount Transceiver Chassis500920 16-Port Rackmount Transceiver Chassis500917 Wall Mount Transceiver Bracket Kit500998 IR Emitter, and 500994 IR Sensor500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU Blade500755 AUDIO / RS232 over IP PoE TransceiverQuick Installation GuideOverviewThe AUDIO / RS232 over IP PoE Transceiver allows 2CH audio signals to be extended up to 330ft(100m) via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transceivers to thesame local Ethernet network, and the device supports PoE (PD) if used with a PoE (PSE) EthernetSwitch. These Transceivers may be purchased individually (part number 500755) or as a kit of twoTransceivers (part number 500755-2PK). The Transceiver supports RS232 and IR transmission forremote control of end devices. The IR Emitter (500998) and IR Sensor (500994) are not included,but if required, may be purchased separately. The Transceiver can be configured as a Transmitteror Receiver.For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch musthave Gigabit ports and DHCP Server capability and additionally support the IGMP communicationprotocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300 SeriesManaged Switches.The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration andutilization of the 500755 and other MuxLab IP based products via an Ethernet web interface.ApplicationsApplications include; commercial and residential AV systems, classroom projector systems, digitalsignage, boardroom systems, collaborative PC systems, and medical information systems, withrespect to the audio portion of these applications.Installation1. The Transceiver must first be set as either a Transmitter or Receiver. This may beaccomplished via the dip switch position #4. Reference the Operating Manual for furtherinstructions on how to set the dip switches. The remaining instructions are based on theTransceiver being set as either a Transmitter or Receiver.2. Identify the connectors on the Transmitter and Receiver as indicated on the product labels,see the above front and rear product views for further details.3. Verify that the distance between the Transmitter and Receiver is within MuxLabspecifications (see Specifications table for further details). |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine