MuxLab 500764-TX Quick Installation Manual

Also see for 500764-TX: Quick installation guide

MuxLab 500764-TX Quick Installation Manual Manual pdf 1 page image

© MuxLab Inc. 94-000921-A SE-000921-A2321 Rue Cohen, Montreal, Quebec, Canada. H4R 2N7Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: info@muxlab.com URL: www.muxlab.comSpecificationsSpecificationsEnvironment HDMI 2.0, resolution of up to 4K/60 (4:4:4)Devices Blu-Ray, Set Top Boxes, Media Players/Streamers, projectors, monitors, TVs, PCs,supporting HDMI.Signal Protocol/Standard HDMI 2.0 and HDCP 2.2Video Bandwidth 594MHzNetwork Bitrate (BW) 32Kbps to 60Mbps for H.264/H.265, and 32Kbps to 200Mbps for MJPGLatency 200ms (in low latency mode with H.265)Protocols Supports Multicast, RTSP, RTMP (H.264), HLS, FLV (H.264), and TSConnectors Two (2) HDMI connectors for AV input and AV Loop-out.One (1) RJ45S for Ethernet connection.Two (2) 3.5mm connectors for 2CH audio embedding and loop-out.One (1) 3.5mm connector for directional IR (direction controllable via software).One (1) RS232 3-Pin Phoenix connector for controlling end devices.One (1) 2.1mm locking power connector.Maximum Distance Cat5e/6: 330ft (100m) from Ethernet Switch. Unlimited over the InternetNote: When installed in an electrically noisy environment, an STP cable must be used.Also, cross-connection reduces the effective distance depending on the grade of twistedcable used.RJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Power Source This device supports PoE (PD), an external power supply is not included. It is intended tobe powered via a PoE (PSE) Ethernet Switch. If required, an optional power supply(500993) may be purchased separately.PoE IEEE 802.3afPower Consumption 7.8WTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingUnit Dimensions 6.1” x 4.4” x 1.0” (154mm x 111mm x 25mm)Shipping Weight 1.1lbs (0.5kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 3 yearsOrder Information 500764-TX HDMI over IP H.264/H.265 PoE Transmitter, 4K/60Accessories(These items are soldseparately)500920 16-Port Rackmount Transceiver Chassis500917 Wall Mount Transceiver Bracket Kit500990 IR Emitter500994 IR Sensor500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU BladeHDMI over IP H.264/H.265 PoE Transmitter, 4K/60500764-TXQuick Installation GuideOverviewThe HDMI over IP H.264/H.265 PoE Transmitter, 4K/60 allows HDMI source equipment to beextended locally up to 330ft (100m) at up to 4K @ 60Hz resolution via Cat5e/6 cable and iscompatible with the Muxlab 500762-RX Receiver to support point-to-point, point-to-multipointand multipoint-to-multipoint configurations, Video Wall and Multiview capabilities in a lowbandwidth expandable and cost effective manner, without the need to install dedicated cablingsystems. The exceptionally low bandwidth requirements of this device in the H.264/H.265 videocodec setting allows for streaming audio/video content over a local network, and over the Internetfor distributed installations spread throughout the globe. The unit also supports a MotionJPG(MJPG) video codec setting for low latency applications. The transmitter accepts a 4K video @60Hz and streams the content to an H.264/H.265 Receiver, such as the MuxLab 500762-RX, to bedisplayed on a 4K monitor. The Transmitter may also send H.264/H.265 video streams to otherH.264/H.265 compatible Receiving devices. The device supports HDMI and 2CH Audio loop-outports, and PoE (PD) and may be powered by a PoE (PSE) Ethernet Switch.The Transmitter (500764-TX) and Receiver (500762-RX) are sold separately. IR Emitter and IRSensor, if required, may be purchased separately for IR based remote control applications.For the point-to-multipoint and multipoint-to-multipoint configurations the Ethernet Switch musthave Gigabit ports, DHCP Server capability and additionally support the IGMP communicationprotocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG350 SeriesManaged Switches.The MuxLab ProDigital Network Controller (500811 or 500812) and MuxControl iOS andAndroid App is available to simplify the configuration and utilization of the 500764-TX and otherMuxLab Av over IP products.ApplicationsApplications include Audio/Video streaming over LAN/Internet, commercial and residential AVsystems, classroom projector systems, digital signage, boardroom systems, and medicalinformation systems.InstallationNote: The following instructions are for the 500764-TX Transmitter and a compatibleReceiver such as the MuxLab 500762-RX Receiver.1. Identify the connectors on the Transmitter and Receiver as indicated on the product labels, see the

/ 2

Related manuals for MuxLab 500764-TX