NAPCO Freedom Wireless Installation Instructions Manual

Contents

NAPCO Freedom Wireless Installation Instructions Manual Manual pdf 9 page image

9* Be aware that the F-8 Control Panel may be programmed to disable Chime.** The LED will not flash if the tamper is held down (if cover is on).F-LTRANS LED** Problem SolutionOne flash every 2 seconds Low battery. Replace battery.Two flashes every 2 seconds F-TAB SensorTrouble.The wire to the F-TAB deadbolt sensor is open or shorted, or the F-TAB dead-bolt sensor is defective. The wires to terminals 1 and 2 shorted should readabout 4 ohms.Four flashes every second Door Shorted. The F-LTRANS wireless transmitter never sensed the door open during the F-TAB deadbolt sensor calibration sequence. Always open the door beforelearning transmitters.F-LTRANS LED INDICATIONSTOUCHPAD LIGHTS (ON FRONT OF TOUCHPAD) FAIL TOTURN ON WHEN POWER APPLIEDCheck F-TP Touchpad power wires (terminals 1 and 2).TOUCHPAD LIGHTS (ON FRONT OF TOUCHPAD) ALLFLASH TOGETHER WHEN POWER APPLIEDGreen wire (terminal 3) either open or shorted.TOUCHPAD RECEIVER LED ON STEADY1. The receiver Touchpad is defective. Replace with a newF-TP Touchpad.2. The receiver Touchpad is located in a noisy RF environ-ment, which may make operation with a Secondarytransmitter difficult.TOUCHPAD RECEIVER LED FLASHING SLOWLY AND DOESNOT RESPOND TO INCOMING TRANSMISSIONSThe receiver is indicating a trouble, and its LED flashesthe number of the transmitter (a sequence of 1 or 2) thatmost recently reported this trouble. Note: The receiverLED will revert to normal operation only after receiving atleast 2 transmissions indicating the transmitter troublewas corrected. For example, if a transmitter low batterytrouble is detected by the receiver, and the faulty trans-mitter is corrected with a new battery, at least two trans-missions with the corrected battery will need to be re-ceived before the receiver LED will revert to normal op-eration. In addition, the touchpad Trouble light can flashup to 4 minutes after the trouble has been corrected.THE TOUCHPAD FAILS TO CHIME* WHEN OPENING THEDOOR:1. The F-TP Touchpad may have a Secondary F-LTRANSwireless transmitter learned into its memory. Check tobe sure that the door this second transmitter is protectingis closed. A door zone is open unless both F-LTRANSdoors are closed.2. Open the F-LTRANS wireless transmitter and check thetransmitter LED flashes. See table below.3. If no Secondary transmitter is intentionally learned, clearthe F-TP Touchpad memory and re-learn the transmitteras follows: Using a pen tip, press and hold the F-TPTouchpad receiver button down (about 6 seconds) untilthe LED turns on steady. Release the button and theLED will flash rapidly, indicating the receiver is in LearnMode with all pre-existing data erased.4. Note: Transmitters CANNOT be programmed with theircovers on. Remove transmitter cover to be tested (coverfor all other transmitters must be installed).Unlock and open door. While pressing and holding thetamper switch, insert battery as shown, then release tam-per switch. For a few seconds, the transmitter will begina self-diagnostic process, then the LED inside the F-LTRANS will flicker, indicating the F-LTRANS is transmit-ting a signal to the receiver.5. With the F-LTRANS cover off and battery installed, pressand release the tamper switch. The Touchpad LED willstop flickering and a chime will sound from the Touch-pad--indicating that the transmitter is successfully pro-grammed into the Touchpad memory.THE SYSTEM DOES NOT ARM1. On the F-TP Touchpad, the green READY light shouldbe on. If the READY light is not on, there is anothermonitored deadbolt in the system (other than the primaryexit door) that is unlocked. All other monitored deadboltsmust be locked for the system to be able to arm.2. Open the F-LTRANS and check the transmitter LEDflashes. See table below.3. If no Secondary transmitter is intentionally learned, clearthe F-TP Touchpad memory and re-learn the transmitteras follows: Using a pen tip, press and hold the F-TPTouchpad receiver button down (about 6 seconds) untilthe LED turns on steady. Release the button and theLED will flash rapidly, indicating the receiver is in LearnMode with all pre-existing data erased.4. Note: Transmitters CANNOT be programmed with theircovers on. Remove transmitter cover to be tested (coverfor all other transmitters must be installed).Unlock and open door. While pressing and holding thetamper switch, insert battery as shown, then release tam-per switch. For a few seconds, the transmitter will begina self-diagnostic process, then the LED inside the F-LTRANS will flicker, indicating the F-LTRANS is transmit-ting a signal to the receiver.5. With the F-LTRANS cover off and battery installed, pressand release the tamper switch. The Touchpad LED willstop flickering and a chime will sound from the Touch-pad--indicating that the transmitter is successfully pro-grammed into the Touchpad memory.TROUBLESHOOTING

/ 12

Related manuals for NAPCO F-TP Touchpad