NAPCO NP-DTM7D24H-D Instructions Manual
    | |
Push Button Layout:PROGRAMMING INSTRUCTIONS:Note: The flashing cursor denotes location of data entry se-lection to be made. If an entry was made in error or requireschanging, depress SET to backspace, make the correct se-lection and depress ENTER to accept data and advance thecursor.A. SETTING CLOCK/CALENDAR:Upon initial power up will appear in display.Depress SET. will appear in display.Depress ENTER. will appear in display.Enter the current date, day of week and time (military) by de-pressing UP and DWN to make the selection then depressENTER to accept.To program Daylight Saving Time (refer to D. Setting BlockEvents (Weekly Repeat) and F. Daylight Saving Time).To change or program clock/calendar simply repeat the stepsabove.B. SETTING EVENTS:Depress SET until "ENTER TO SET EVENT" appears in display.Depress ENTER. will appear in display.Note: A01 indicates Channel A event 01.When cursor appears you are able to scroll through events.Depress ENTER until the flashing cursor appears under OFFin display. Now select type of event required by scrolling us-ing the UP and DWN push buttons until either:ON - Relay ON (latching mode).OFF - Relay OFF (latching mode).PL - Relay Pulse (momentary)....appears in display and depressing ENTER will make theselection.When selecting the pulse mode, PL01 will appear in the dis-play. It is now necessary to assign the length of time (durationof relay activation). The pulse can range in length from 1-second minimum to 15-seconds maximum and is selected byusing UP or DWN push buttons, and then depressing ENTERto accept.Note: If pulse duration is not selected, relay output defaults to1-second. Next, select the day of the week or BK* for weeklyrepeat and time (military) by scrolling using UP and DWNpush buttons and depressing ENTER to accept. You maycontinue to program events by repeating the previous steps orexit programming by depressing SET.Note: When programming additional events, it is necessaryto select the next consecutive event number following the lastevent program to continue.Note: When it is required to have the same event repeatedon two (2) programmed as a block by selecting BK in the dayfield.Note: To program the consecutive days of the week, refer toD. Setting Block Event (Weekly Repeat) and F. DaylightSaving Time.C. ADDING EVENTSDepress SET until "ENTER TO SET EVENT" appears in display.Depress ENTER. will appear in display.Depress ENTER. If the event is not programmed, the cursorwill move to the OFF (relay function) position. If the event isprogrammed, the cursor will move to the position and the pro-grammed information of the event will be displayed. At thispoint, depress the UP button to step up through the pro-grammed events. When an unprogrammed event is reached,the cursor will move to the OFF (relay function position). (Atthis point, see Setting Events or Setting Holiday Events).D. SETTING BLOCK (WEEKLY REPEAT)Select channel A or B by moving slide switch SW1 to ap-propriate position.Note: Channel cannot be changed in the middle of program-ming events. To change channels, you must exit program-ming, then change channel switch position, then enter pro-gram mode again.Depress SET until appears in display.Push Button Description TablePushButtonFunction/DescriptionSET Scrolling keys for programming. Escaping out ofexisting programming.ENTER Accepts selections made to programming.UP Scrolls through selections.DWN Scrolls through selections.UP and DOWN keys can be used to select data entries.After scrolling to the correct entry, depress ENTER to ac-cept.SW1 clip SW Selects channel to be programmed.SW2 slide SW Selects tandem or individual relay operation.(CUT R3)CH ONSU 01:01ENTER TOSET TIME01/01/01SU / 01:01A01 OFFSU 00:00A01 OFFBK 00:00A01 OFFSU 00:00ENTER TOSET BKLithium Battery Socket(order Model CR2032)12-24 VoltAC/DC input |
Related manuals for NAPCO NP-DTM7D24H-D
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine