NEC 42XR3 Model Information

Also see for 42XR3: Operation manual Supplementary guide Supplementary guide Brochure Installation guide

NEC 42XR3 Model Information Manual pdf 25 page image

E-21Option1 Settings MenuSetting the on-screen menuThis sets the position of the menu, the display format(horizontal or vertical) etc.Example: Turning the DISPLAY OSM offOn “OPTION1” menu, select “OSM”, then press the MENU/ENTER button.The “OSM” menu appears.On “DISPLAY OSM” of “OSM” menu, select “OFF”.OSMEXITDISPLAY OSMOSM ADJ.OSM ANGLEOSM ORBITEROSM CONTRAST: OFF: 1: H: OFF: LOWSEL. RETURNADJ.Information DISPLAY OSM settingsON: The on-screen menu appears.OFF: The on-screen menu does not appear.If you press the DISPLAY button on the remote controlfor more than 3 seconds the main menu will appearand can be set (although it is not ON). OSM ADJUST settingsAdjusts the position of the menu when it appears onthe screen.The position can be set between 1 to 6. OSM ANGLE settingsSets the display format (landscape “H” or portrait “V”).When the unit is installed vertically set the OSMANGLE at “V”.“H” “V”OPTION1 1 / 4EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: AUTO: 1080B: OFF: OFFSEL. RETURNMENU/ENTER OK OSM ORBITER settingsON: The position of the menu will be shifted by eightdots each time OSM is displayed.OFF: OSM will be displayed at the same position. OSM CONTRAST settingsNORMAL: OSM brightness is set to normal.LOW: OSM brightness is set to lower.OPTION1EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESET: RGB: RGB: AUTO: 1080B: OFF: OFF1024768SEL.RETURNMENU/ENTER OKSetting the BNC connectorsSelect whether to set the input of the 5 BNC connectors toRGB, component or SCART1,2.Example: Set the BNC INPUT mode to “COMP.”On “BNC INPUT” of “OPTION1” menu, select “COMP.”.OPTION1 1 / 4EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: COMP.: RGB: AUTO: 1080B: OFF: OFFSEL. RETURNADJ.Information BNC INPUT SettingsRGB: Use the 5BNC terminals for RGB input.COMP.: Use the 3BNC terminals for component input.SCART1: Use the 4BNC terminals for RGB withcomposite sync. See page E-8.SCART2: Use the 3BNC terminals for RGB and theVIDEO1 terminal for composite sync. See page E-8.Setting the RGB1 connectorSelect one of the signals being transmitted to the RGB1terminal.Example: Set the D-SUB INPUT mode to “SCART3”On “D-SUB INPUT” of “OPTION1” menu, select“SCART3”.OPTION1 1 / 4EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: SCART3: AUTO: 1080B: OFF: OFFSEL. RETURNADJ.Information D-SUB INPUT SettingsRGB: Use the D-SUB terminal for RGB input.SCART3: Use the D-SUB terminal for RGB signal fedfrom SCART. See page E-8.Setting a computer image to the correct RGBselect screenWith the computer image, select the RGB Select modefor a moving image such as (video) mode, wide mode ordigital broadcast.Example: Setting the “RGB SELECT” mode to“MOTION ”On “RGB SELECT” of “OPTION1” menu, select“MOTION”.OPTION1 1 / 4EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: MOTION: 1080B: OFF: OFFSEL. RETURNADJ.