NEC MD215MG-S5 Installation & Maintenance Manual

Also see for MD215MG: Specification

Contents

NEC MD215MG-S5 Installation & Maintenance Manual Manual pdf 8 page image

English-5EnglishRecommended useSafety Precautions and MaintenanceFOR OPTIMUM PERFORMANCE, PLEASE NOTETHE FOLLOWING WHEN SETTING UP ANDUSING THE LCD GRAYSCALE MONITOR:• DO NOT OPEN THE MONITOR OR AC ADAPTER. There are no user serviceable parts inside and opening or removingcovers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualifi ed service personnel.• Do not spill any liquids into the cabinet or use your monitor near water.• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful orfatal or may cause electric shock, fi re or equipment failure.• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fi re.• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage tothe monitor.• The power supply cord you use must have been approved by and comply with the safety standards of your country.• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.• Do not place any objects onto the monitor and do not use the monitor outdoors.• Use the supplied AC Adapter. Do not place any objects onto the AC Adapter and do not use the AC Adapter outdoors.• The lamps in this product contain mercury. Please dispose according to state, local or federal law.• Do not bend, crimp or damage the power cord.• Do not use monitor in high temperatured, humid, dusty, or oily areas.• Do not cover vent on monitor and AC Adapter.• Vibration can damage the backlight. Do not install the monitor where it will be exposed to continual vibration.• If the monitor's LCD panel is broken, do not come in contact with the liquid crystal and handle with care.• To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install themonitor in a stable location and take measures to prevent falling.Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing toqualifi ed service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall, fi reand electric shock:• If the monitor stand has been cracked or peeled.• If the monitor has been wobbled.• If the monitor emanates an unusual odor.• When the power supply cord or plug is damaged.• When the AC Adapter is damaged.• If liquid has been spilled, or objects have fallen into the monitor.• If the monitor has been exposed to rain or water.• If the monitor has been dropped or the cabinet is damaged.• If the monitor does not operate normally by following operating instructions.• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilatedopenings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.• The power cable connector is the primary means of detaching the system from the power supply.The monitor should be installed close to a power outlet which is easily accessible.• Handle with care when transporting. Save packaging for transporting.• Do not touch LCD panel surface while transporting, mounting and setting. Applying pressure on the LCDpanel can cause serious damage.• Carry the monitor by holding the top and the bottom of the monitor head with both hands.• Do not carry holding only the stand.Image Persistence: Image persistence exists, when a residual or “ghost” image of a previous image remains visible on thescreen. Unlike with CRT monitors, image persistence on LCD monitors is not permanent, but constant images being displayedfor a long period of time should be avoided.To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an imagewas on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regularintervals whenever the screen is idle or turning off the monitor when not in use.Maintenance: This display is factory calibrated for diagnostic imaging, in accordance with DICOM Part 14. To ensure constantvisual quality over the life of this display, the recommended time interval to re-calibrate this model is 12 months.CAUTION