NEC MultiSync LCD2090UXi User Manual

Also see for LCD2090UXI - MultiSync - 20.1" LCD Monitor: Specifications Specification Specifications Specifications Brochure & specs

EnglishEnglish-19Tag3 Auto Adjust Automatically adjusts the Image Position and H.Size settings and Fine settings.(Analog input only) Press “SELECT” to activate Auto Adjustment.Signal Adjust Determines when the auto adjustment is activated automatically.(Analog input only) The choices are “SIMPLE” and “FULL”. Press “Left” or “Right” to select.Auto Adjust Level Determines the automatic adjustment level for Auto Adjust. The choices are “SIMPLE”,(Analog input only) “FULL” and “DETAIL”. Press “Left” or “Right” to select. Refer to the below table.A-NTAA SW The Advanced No Touch Auto Adjust function is able to recognize new signals even when(Analog input only) neither the resolution nor the refresh rate has changed. If several PCs are connected tothe monitor, and each transmit very similar (or even the same) signals in terms ofresolution and refresh rates, the monitor recognizes that there is a new signal andautomatically optimizes the picture without the need for any action on the part of the user.OFF: A-NTAA is disabled.ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal settingsfor the new signal. If no change in the signal is detected then A-NTAA does not activate.The screen will be blank while the monitor optimizes the signal.OPTION: Functions the same as ON, except that the screen does not go blank when themonitor makes adjustments for changes in signal, allowing the monitor to display the newsignal faster. When using an external switching device to connect 2 or more PCs to themonitor, using the ON or OPTION settings is suitable.Tag4 H. Position Controls Horizontal Image Position within the display area of the LCD.Press “Left” or “Right” to adjust.V. Position Controls Vertical Image Position within the display area of the LCD.Press “Left” or “Right” to adjust.H. Size Adjusts the horizontal size of the screen.(Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a furthertuning can be performed using the “H.Size (V.Size)” function (dot clock). For this a Moirétest pattern could be used. This function may alter the width of the picture. Use left/RightMenu to center the image on the screen. If the H.Size (V.Size) is wrongly calibrated, theresult would look like on the left drawing. The image should be homogeneous.Fine Improve focus, clarity and image stability by increasing or decreasing this setting.(Analog input only) If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactorypicture setting, a fine tuning can be performed using the “Fine” function. For this a Moirétest pattern could be used. If the Fine value is wrongly calibrated, the result would looklike on the left drawing. The image should be homogeneous.Auto Fine This function automatically and periodically adjusts the “FINE” setting for change in signal(Analog input only) condition. This function adjusts approximately every 33 minutes.H. Resolution Adjusts the horizontal size by increasing or decreasing the setting.Press “Right” button to expand the width of the image on the screen.Press “Left” button to narrow the width of the image on the screen.V. Resolution Adjusts the vertical size by increasing or decreasing the setting.Press “Right” button to expand the height of the image on the screen.Press “Left” button to narrow the height of the image on the screen.Expansion Sets the zoom method.FULL: The image is expanded to 1600 x 1200, regardless of the resolution.ASPECT: The image is expanded without changing the aspect ratio.OFF: The image is not expanded.CUSTOM: When CUSTOM is selected as the Expansion mode, it becomes possible toadjust the H. ZOOM., V. ZOOM, and ZOOM POS.H-size, Fine, H/V Position ContrastSIMPLE O XFULL O OO: Automatic Adjustment X: No Automatic AdjustmentNOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.Size, Fine, Position Contrast Black Level, TimeLong cable capability**SIMPLE O X X 1 secondFULL O O X 1.5 secondsDETAIL* O O O 5 secondsO: Automatic Adjustment X: No Automatic Adjustment* “DETAIL” activates automatic long cable (skew, peaking) adjustment.** Black level, RGB sharpness, RGB delay and RGB position are adjusted using “Long cable software”which is included in the attached CD-ROM.