N8120-102Desk/LCD Mount KitInstallation and Handling Guide856-122303-102-00 First Edition, October 2007PrefaceCongratulations for your purchase of our product.N8120-102 Desk/LCD Mount kit is used for installation ofUS110.Before installing or removing the product, read thoroughlythis guide and the User's Guide of the US110. Keep thisguide in a safe place for future use.Safety PrecautionsFollow instructions given in this guide for proper operationsand safe use of the product.See also "Notes on Safety" described in the "US110 User'sGuide" that comes with your US110 before installing the product.Be sure to unplug the power cord of the US110 before startinginstallation.Observe instructions given in this guide and the "US110 User'sGuide" to use the US110 safely. Failure to follow theseinstructions may cause a fire, personal injury, or propertydamage.WARNING Indicates the presence of a hazard that may resultin death or serious personal injury.Step 1 Checking ComponentsThe shipping carton contains the following components.Installation and Handling Guide*1 Each of two Desk/LCD Mount kits has the same shape.Step 3 Installation (Cont'd)Then, insert another projection into another hole on theUS110, and fix the US110 to the bracket.3. Attach the two tie wraps for securing cables to thebracket.Step 2 Before Starting Installation1. Quit all the application programs and shutdown thesystem.2. Power off the US110, and unplug the power cord.WARNINGBe sure to power of the US110 and unplug the powercord. If the US110 is off-powered but its power cord isplugged to a power source, touching an internalcomponent may cause an electric shock.Do not disconnect the power cord while your hands arewet. Doing so may cause an electric shock.3. Disconnect all the cables from the US110.Step 3 InstallationThe US110 can be installed using the Desk/LCD Mount kit inthe following two ways:– Place the US110 vertically on the desk by using theDesk/LCD Mount kit as stabilizers.– Install the US110 to the rear of the LCD unit by using theDesk/LCD Mount kit as brackets.< When used as stabilizers> If you want to install the US110 in the desired positionof the LCD unit, it is recommended to use N8120-103LCD mount adjuster option additionally.If you want to place the US110 on the desk, see "UsingUS110 on Desktop" described later.If you want to install the US110 to the rear of LCD unit, see"Installing US110 to the LCD Unit" described later.4. Secure cables to be connected to the US110 with tiewraps.Secure cables as shown in the figure below.Installing US110 to the LCD Unit1. Secure the two brackets to the rear of the LCD unit withscrews.As shown in the figure below, secure the two brackets tothe rear of LCD unit with two screws for each.Using US110 on Desktop1. Assemble two brackets.As shown in the figure below, cross the two brackets.Align the projection on either bracket with the hole on theother bracket.The two brackets must be assembled as shown in thefigure below.2. Fix the US110 to the assembled bracket.Align the rear face of US110 with the marking formounting on the bracket, then insert a projection of thebracket into the hole on the US110.2. Fix the US110 to the bracket.Place the US110 so that its rear panel faces downward,as shown in the figure below. Engage the hook of thebracket with cavity at either side of the US110, thenengage another hook with the cavity at another side.Push the US110 until it is fixed.Rear face of US1103. Attach the two tie wraps for securing cables to thebracket.Pass the tie wraps through the lower holes of the bracketso that they can secure the cables to be connected tothe connectors of the US110.4. Secure cables to be connected to the US110 with tiewraps.Removal Procedures1. Quit all the application programs and shutdown thesystem.2. Power off the US110, and unplug the power cord.3. Disconnect all the cables from the US110.Remove the tie wraps and disconnect all the cables.4. Remove the US110 from the bracket.Transfer to Third PartyWhen you transfer or sell this product to a third party, includeall the attachments including this guide.DisposalDispose of the product according to all national laws andregulations. NEC Corporation 2007No part of this manual may be reproduced in any form without theprior written permission of NEC Corporation.US110BracketsProjection HoleHoleBracketsRear face ofUS110Marking formountingTie wraps (2 pcs.)Desk/LCDMount kit(2 pcs.)*1Screws (4 pcs.)Bottom of US110Rear face ofUS110Tie wrapsFront face ofUS110BracketsTie wraps
