NEC PX-42VR5W User Manual

NEC PX-42VR5W User Manual Manual pdf 23 page image

E-19SET UP Settings MenuSetting the language for the menusThe menu display can be set to one of eight languages.Example: Setting the menu display to “DEUTSCH”On “LANGUAGE” of “SET UP” menu, select “DEUTSCH”.SEL. ADJ. EXIT RETURNSET UPLANGUAGEBNC INPUTD-SUB INPUTHD SELECTRGB SELECTDVI SET UPCOLOR SYSTEMBACK GROUNDGRAY LEVELS1/S2DISPLAY OSMOSM ADJ.ALL RESET: DEUTSCH: COMPONENT: RGB: 1080I: AUTO: AUTO: GRAY: 3: OFF: ON: TOP LEFT: OFFInformation Language settingsENGLISH ........ EnglishDEUTSCH ....... GermanFRANÇAIS ...... FrenchESPAÑOL ....... SpanishITALIANO ........ ItalianSVENSKA ....... Swedish................... ChineseУ ............ RussianSetting the BNC connectorsSelect whether to set the input of the 5 BNC connectors toRGB and component or SCART1, 2.Example: Set the BNC INPUT mode to “RGB”On “BNC INPUT” of “SET UP” menu, select “RGB”.SEL. ADJ. EXIT RETURNSET UPLANGUAGEBNC INPUTD-SUB INPUTHD SELECTRGB SELECTDVI SET UPCOLOR SYSTEMBACK GROUNDGRAY LEVELS1/S2DISPLAY OSMOSM ADJ.ALL RESET: ENGLISH: RGB: RGB: 1080I: AUTO: AUTO: GRAY: 3: OFF: ON: TOP LEFT: OFFInformation BNC INPUT SettingsRGB: Use the 5BNC terminals for RGB input.COMPONENT: Use the 3BNC terminals forcomponent input.SCART1: Use the 4BNC terminals for RGB withcomposite sync. See page E-7.SCART2: Use the 3BNC terminals for RGB and theVIDEO1 terminal for composite sync. See page E-7.Setting the RGB1 connectorSelect one of the signals being transmitted to the RGB1terminal.Example: Set the D-SUB INPUT mode to “SCART3”On “D-SUB INPUT” of “SET UP” menu, select “SCART3”.SET UPLANGUAGEBNC INPUTD-SUB INPUTHD SELECTRGB SELECTDVI SET UPCOLOR SYSTEMBACK GROUNDGRAY LEVELS1/S2DISPLAY OSMOSM ADJ.ALL RESET: ENGLISH: COMPONENT: SCART3: 1080I: AUTO: AUTO: GRAY: 3: OFF: ON: TOP LEFT: OFFSEL. ADJ. EXIT RETURNSetting high definition images to the suitablescreen sizeUse this procedure to set whether the number of verticallines of the input high definition image is 1080I or 1035Ior 540P.Example: Setting the “HD SELECT” mode to “1035I”On “HD SELECT” of “SET UP” menu, select “1035I”.SEL. ADJ. EXIT RETURNSET UPLANGUAGEBNC INPUTD-SUB INPUTHD SELECTRGB SELECTDVI SET UPCOLOR SYSTEMBACK GROUNDGRAY LEVELS1/S2DISPLAY OSMOSM ADJ.ALL RESET: ENGLISH: COMPONENT: RGB: 1035I: AUTO: AUTO: GRAY: 3: OFF: ON: TOP LEFT: OFFInformation HD SELECT modesThese 3 modes are not displayed in correct imageautomatically.1080I: Standard digital broadcasts1035I: Japanese “High Vision” signal format540P: Special Digital broadcasts (for example :DTC100)Information D-SUB INPUT SettingsRGB: Use the D-SUB terminal for RGB input.SCART3: Use the D-SUB terminal for RGB signal fedfrom SCART. See page E-7.Setting a computer image to the correct RGBselect screenWith the computer image, select the RGB Select modefor a moving image such as (video) mode, wide mode ordigital broadcast.Example: Setting the “RGB SELECT” mode to“MOTION ”On “RGB SELECT” of “SET UP” menu, select “MOTION”.SEL. ADJ. EXIT RETURNSET UPLANGUAGEBNC INPUTD-SUB INPUTHD SELECTRGB SELECTDVI SET UPCOLOR SYSTEMBACK GROUNDGRAY LEVELS1/S2DISPLAY OSMOSM ADJ.ALL RESET: ENGLISH: COMPONENT: RGB: 1080I: MOTION1024768: AUTO: GRAY: 3: OFF: ON: TOP LEFT: OFFInformation RGB SELECT modesOne of these 7 modes must be selected in order todisplay the following signals correctly.AUTO: Select the suitable mode for the specificationsof input signals as listed in the table “Computer inputsignals supported by this system” on page E-2 of ModelInformation.STILL: To display VESA standard signals. (Use thismode for a still image from a computer.)MOTION: The video signal (from a scan converter)