Manuals database logo
manualsdatabase
Your AI-powered manual search engine

NIDEC TOSOK DAG2000 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Contents
  1. Table Of Contents
  2. CHAPTER 1 INTRODUCTION
  3. Block Diagram
  4. CHAPTER 2 NAME AND FUNCTION OF EACH PART
  5. CHAPTER 3 PROCEDURE UP TO MEASUREMENT
  6. For work tolerance (judgment limits) change cases
  7. For first time measurement tool connection cases
  8. For several measurement tools connection cases
  9. CHAPTER 4 MASTER CALIBRATION
  10. Master calibration by 1 master
  11. Clearing of master data
  12. CHAPTER 5 MEASUREMENT
  13. CHAPTER 6 DETAILS OF EACH PROCEDURE
  14. Starting
  15. Settings
  16. Detector Adjustment
  17. Program Switching
  18. CHAPTER 7 EXTERNAL I/O FUNCTION
  19. External button input
  20. CHAPTER 8 MAINTENANCE
  21. CHAPTER 10 OTHERS
  22. Specifications
  23. CHAPTER 11 WORKSHEET
NIDEC TOSOK DAG2000 User Manual Manual pdf 13 page image
DIGITAL AIR MICROMETER USERS MANUAL (Second Edition)134.2 Master calibration by 1 masterShown here is the method on how to perform ZERO correction by ZERO master.Valid for cases when [ZERO M.] in the [CAL MODE] settings item is selected.Sensitivity correction data will use the master calibration results of the 2 masters performed previously.If 2 masters adjustment has not been performed,please perform first [Chapter 6, 6.5 DetectorAdjustment].Confirmation of masterand measurement toolMeasurement modeSwitch to mastercalibration mode (mastercalibration)ZERO master calibration(ZERO correction)Master calibrationcompletionh “MAS OK” will be shown in the English display and will switch tomeasurement mode.Master calibration has error if anything else is displayed.Please press ENT and repeat from f.About the master calibration error, please refer to [3.4 MasterCalibration Error].g Please set the ZERO master to the measurement tool.Raw data (without correction) is displayed in the main display.Raw data display colors are:• When color is green, ZERO master calibration is possible.Please press ENT. ZERO correction will be performed.• When color is red, ZERO master calibration is not possible.Detector adjustment will be performed.Please press / MAS .“ADJ.” will be shown in the English figures display and willswitch to detector adjustment.Please refer to [Chapter 6, 6.5 Detector Adjustment] for details.f After “MIN M.” in the English display has been displayed for 2seconds, raw data will be displayed.Mode lamp [MAS] with orange color with light up.c Please confirm that there are no foreign objects sticking on themaster or measurement tool. In case there are foreign objects, thiswill have bad effect on the master calibration and measurementcannot be performed correctly.d Please confirm that it is in measurement mode (mode lamp [MEAS]will light up).Please refer to [Chapter 5 Measurement] for detailse Press/MAS continuously for 2 seconds.Will switch from measurement mode to master calibration mode(master calibration)
/ 33
This manual is suitable for:
DAG2000
Manuals database logo
manualsdatabase
Your AI-powered manual search engine