NTI Trinity Lx 150 Installation And Operation Instructions Manual

Also see for Trinity Lx 150: Installation and operation instructions Installation and operation instructions Installation and operation instructions

Contents

NTI Trinity Lx 150 Installation And Operation Instructions Manual Manual pdf 3 page image

Lx Series Installation and Operation Instructions │Trinity Lx31.0 INTRODUCTIONInstallation and Operation Instructions – These instructions apply to the installationand operation of Trinity Lx150-800 units and covers instructions that are common-to-both boiler and water heater applications. Troubleshooting instructions for the controller and display arecovered in Appendix A. Appliance-specific plumbing and wiring instructions for Boilers and Water Heatersare covered in Appendix B and C, respectively.Terminology – The following terms in the instruction manuals are used to differentiate between whichinstructions are common-to-both and which are appliance-specific. The term "APPLIANCE" applies to bothkinds of water heating appliances (boilers and water heaters) and is used when conveying instructions whichare common-to-both. The term "BOILER" or "WATER HEATER" is used when conveying instructionswhich are appliance-specific or specific to one or the other, but not both.Table 1-1 Instruction ManualsAppliance Model No. Common-to-Both(Trinity Lx Series)Appliance-Specific(Application Based)Boiler Lx150-800Installationand OperationInstructionsAppendix A - Controllerand TouchscreenDisplay InstructionsAppendix BBoiler Applications:Plumbing and WiringInstructionsn/aWaterHeater Lx200-800Installationand OperationInstructionsAppendix A -Controllerand TouchscreenDisplay Instructionsn/aAppendix CWater HeatingApplications:Plumbing and WiringInstructionsNotes1 A conversion kit is required to convert models Lx150-400 so they will safely operate with Propane Gas.2 No conversion kit is required to operate the Lx500 on Propane (LP), see Section 9.0 for specific instructions.3 Do not convert the Lx600, Lx700 or Lx800 to Propane (LP). Operate with Natural Gas only.General Installation RequirementsThe installation of your NTI Trinity Lx gas appliance must conform to the requirements of this manual, yourlocal authority, and the National Fuel Gas Code ANSI Z223.1 and or CAN/CGA B149 Installation Codes.Where required by the Authority, the installation must conform to the standard for “Controls and Safety Devicesfor Automatically Fired Boilers ANSI/ASME CSD-1.This document pertains to the correct installation and operation of NTI Trinity boiler models Lx150, Lx150E,Lx200, Lx300, Lx400, Lx500, Lx600, Lx700 and Lx800. The instructions detailed in this document supersedeany and all previous instructions provided by NTI, written or otherwise. Each unit is provided with variousmanuals and a Natural to LP Conversion Kit for applicable models. Refer to notes and list of InstructionManuals in Table 1-1.Lx 600-700-800 models are not approved for operation with Propane (LP Gas). Failure tocomply with these instructions will result in property damage, serious injury or death.Read and understand this entire document prior to proceeding with the installation of theTrinity Lx. Failure to follow the instructions outlined in this document will result inproperty damage, serious injury or death.User ResponsibilitiesThis appliance must be installed and serviced by a qualified installer or service technician. This appliance mustbe serviced and inspected annually when operating in normal residential applications. Demanding applicationsor extreme conditions (i.e. commercial) may require more frequent service and inspection. As the User/Owner ofthis equipment, you are responsible for ensuring the maintenance is performed at the required intervals.Failure to have the appliance properly serviced and inspected on a regular basis by aqualified service technician may result in property damage, serious injury or death.Failure to keep the Vent and Combustion Air Intake clear of ice, snow, and otherdebris may result in property damage, serious injury, or death.