Nakanishi SHEENUS neo Operation Manual
Also see for Sheenus neo: Operation manual
  | |
Contents | 
SHEENUS neoOM-K0518EOPERATION MANUALThank you for purchasing the Ultrasonic Polisher SHEENUS neo.SHEENUS neo has a wide variety of finishing tools such as diamond stone, diamond file, ceramic stone and woodenlapping toolsPlease read this Operation Manual carefully prior to use.A. GROUNDING INSTRUCTIONS1) In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current toreduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-groundingconductor and a grounding plug. The plug must be plugged into a matching outlet that is properlyinstalled and grounded in accordance with all local codes and ordinances.2) Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.3) Improper connection of the equipment-grounding conductor can result in a risk of electric shock.The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect theequipment-grounding conductor to a live terminal.4) Check with a qualified electrician or service personnel if the grounding instructions are not completely understood,or if in doubt as to whether the tool is properly grounded.5) Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool'splug.6) Repair or replace damaged or worn cord immediately.7) (120V)This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A inFigure(below). The tool has a grounding plug that looks like the plug illustrated in Sketch A in Figure(below). Atemporary adapter, which looks like the adapter illustrated in Sketches B and C, may be used to connect this plug toa 2-pole receptacle as shown in Sketch B if a properly grounded outlet is not available. The temporary adaptershould be used only until a properly grounded outlet can be installed by a qualified electrician. The green-coloredrigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as aproperly grounded outlet box.NOTE:Adopter(Figure B)not for use in Canada.Grounding Method8) USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extensioncord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause adrop in line voltage resulting in loss of power and overheating. Table(below)shows the correct size to use dependingon cord length and nameplate ampere rating. If in doubt, use the next heavler gauge. The smaller the gaugenumber, the heavier the cord.Minimum gauge for cordB. WARNING1) Always wear safety glasses. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.Also use a dust or face mask whenever the motor is running.2) Make sure to connect the earth cables to ground before use.3) Do not use near flammable substances or in explosive atomospheres. Contact with flammable substances while thesystem is operating may cause a fire.4) Keep Sheenus neo away from moisture, dust, corrosive gas and direct sunlight.5) Ultrasonic vibration may cause noise during use. Earplugs would be recommended.6) Do not block off the ventilation on the back/bottom of Sheenus neo.7) Contamination or scratches on the tool thread, the handpiece or the ultrasonic horn may cause abnormal vibrationor overheat.8) Attach the tool firmly to the ultrasonic horn. If the tool is not attached firmly, the power would go down or thehanpiece would overheat.9) The tool or the tool holder would heat up due to ultrasonic vibration even though under normal conditions. Holdingthem tightly or pressing against the skin may cause burn.10) Do not hit hardly or disassemble. It may affect the products performance and safety. Send to the dealer where youpurchased for repair.11) Keep the handpiece from oil. It may cause the handpiece failure. Do not spray cutting oil or lubricate the handpiece.12) Do not disassemble the control unit. There is a high voltage area on the circuit board and you may get electricshock.C. CAUTION1) Use at room temperature 10 degrees to 40 degrees under no condensation. Failure to follow this may cause ashort circuit or electric shock.2) Check the condition before use. If any abnormality is found, return to the dealer where you purchased for repair.D. INFORMATION1) SHEENUS NEO utilizes an ultrasonic transmitter. It may affect computers and LAN cables nearby. Also radioreceivers may pick up noise.2) Turn off the power switch after use. If you don’t use for a long time, unplug the power cord.3) Users are responsible for safe operation and maintenance.(1) Control Unit (2) Handpiece(3) Standard EquipmentsSpecial tip holder (Round for 3.0mm)Special tip holder (Flat for t=1.0mm)Ceramic fiber grindstone#800 (Flat 650mm t=1)Electroplated diamond file#200 (Flat taper4 50mm t=0.4)(1) Standard Set1 Cautions for handling and operation2 SpecificationsRead these cautions carefully and only use in the manner intended.Safety instructions are intended to avoid potential hazards that could result in personal injury or damage to thedevice. Safety instructions are classified as follows in accordance with the seriousness of the risk.4 Preparation before use5 Attachment of the toolClass Degree of RiskWARNING A hazard that could result in bodily injury or damage to the device if the safetyinstructions are not followed.CAUTION A hazard that could result in light or moderate bodily injury or damage to the device if thesafety instructions are not followed.INFORMATION Be sure to keep the usage for your safety.Ampere RatingVolts Total length of cord120V240V7.5m(25ft.) 15m(50ft.) 30m(100ft.) 45m(150ft.)15m(50ft.) 30m(100ft.) 60m(200ft.) 90m(300ft.)MoreThan06101261012161818161416161612161414141212Only the applicable parts of the Table need to be included. For instance, a 120-voltproduct need include the 240-volt heading.Not RecommendedNot MoreThanu Display Select SwitchFig.2r Power Switcht UNCLAMP/CLAMP Switchy ON/OFF Switchi Displayo Power Control Knob!0 Socket for connectionghandpieceFig.3!1 Socket for Foot Switch !2 Power InletFig.4!3 !4 !6 !5 !7 Fig.5!3 Protector Sleeve !4 Test ToolFig.6r Power Switch!0 Socket for connectinghandpieceHandpiece PlugFig.7!2 Power InletPower CordFig.8!1 Socket ForFoot SwitchPlugTo The Foot SwitchFig.9(2) Front of Sheenus neo(3) Back of Sheenus neo(4) Handpiece(1) The test tool !4 comes with the handpiece. Remove the protector sleeve !3 and unscrew the test tool !4 using thetwo provided wrenches. ( The test tool !4 is attached to the handpiece and intended for testing the vibration of thehandpiece.)(2) Insert the output plug of the handpiece into theoutput receptacle !0 of the Sheenus neo.(3) Make sure that the power switch r is off, andconnect the power cord to the power inlet !2.(4) When using the foot switch (FC-24), connect thefoot switch plug to the foot switch receptacle !1.(1) Attachment of one piece holders, tip holders and connecting adaptorsAttach the holder or the connecting adaptor to the handpieceand clamp tightly using two provided wrenches ( see fig.9).Then attach the protector sleeve.(2) Attachment of Tip tools (e.g. ceramic grind stone tip)Insert the grind stone tip to the tip holder and tighten the screwusing the provided allen wrench. If the clearance between thegroove of the tool holder and the tool is large, do not force putin a thin metal plate. And attach the protector sleeve.(3) M4 screw connecting adaptorAttach the M4 screw connecting adaptor !7 to the handpieceand clamp tightly using the two provided wrenches. Thenattach the M4 tool and clamp using the wrenches, and attachthe protector sleeve.If the tool or the tool holder is loose, vibration will be weak and cause noise or overheat.(1) Power switch rTurn on/off the power.(2) Unclamp/Clamp Switch tThere are two modes of Unclamp and Clamp.Unclamp modeUse Unclamp mode when one-piece tools are attached.Clamp modeUse Clamp mode when a tip holder is attached using unclamp mode for the tip holder may burn and break thetool due to too much vibration.(3) On/Off switch yThis is to start or stop the control unit. The On LED lamp (green) is on at start up and during normal operation theoff LED lamp (green) is when shutdown. When the protection circuit stops the control unit, the Reset LED lamp (red)lights up and the control unit will need to be restarted by pressing the reset button twice after correcting the problem.(4) Display switch uBy pressing the Display switch, the LED display can be changed from Watt/ Power.(5) Display iThe selected Watt/Power value is shown on the display.Watt : Electric power supplied to the oscillator is shown.The heat generated in the had piece, tool holder and tool is proportional to the power applied to the oscillator,too much power will cause the handpiec, tool holder and tool to overheat and possibly burn. If the handpiece,tool holder or tool becomes hot, lower the power setting. USE GREAT CARE TO AVOID TOUCHING THETOOL HOLDER AND TOOL DURING WORKING AS THEY CAN CAUSE SEVERE BURNS.Power : Output level is shown.Applicable display range is 0 49. (with the test tool, Unclamp mode is 19 49, Clamp mode 8 23.)(6) Power control knob oTurn the Power Control knob o to control the output.Fig.10Allen WrenchSet ScrewToolCaution on attaching the tool3 Nomenclatureq Foot Switch(FC-24)w Control unit(NE240)e Handpiece(US-25PB)Fig.16 Detail of the operational partsFig.11y ON/OFF Switch u Display Switchi Displayo Power Control Knobt UNCLAMP/CLAMP Switchr Power SwitchModel US-25PBOscillator PZT piezoelectric typeCord length 2mWeight 140g(excluding cable)Unit Model NE240Oscillation frequency 22.5KHzFrequency Control Homing TypeOutput 45W max.(UNCLAMP MODE)20W max.(CLAMP MODE)AC120V, 50/60HzAC230V, 50/60HzAC120V : T1.6AL 250VAC230V : T800mAL 250VPower Conditioning Continuous variable typePower SourceRating Input 50VAAppropriate fuseDimensions W225 D195 H97mmWeight 2.1kg |
Related manuals for Nakanishi Sheenus neo
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine