Napoleon BGD36CFNTR Installation And Operating Instructions Manual

Also see for BGD36CFGN-1: Installation and operating instructions

Contents

Napoleon BGD36CFNTR Installation And Operating Instructions Manual Manual pdf 2 page image

2W415-1132 / C / 08.20.13ENTABLE OF CONTENTSNOTE: Changes, other than editorial, are denoted by a vertical line in the margin.1.0 INSTALLATION OVERVIEW 32.0 INTRODUCTION 42.1 DIMENSIONS 52.1.1 BGD36CF / BGD36CFG 52.1.2 GD36M 52.2 GENERAL INSTRUCTIONS 52.3 GENERAL INFORMATION 72.4 RATING PLATE INFORMATION 73.0 VENTING 83.1 VENTING LENGTHS AND COMPONENTS 83.2 TYPICAL VENT INSTALLATIONS 93.3 SPECIAL VENT INSTALLATIONS 113.3.1 PERISCOPE TERMINATION 113.3.2 CORNER TERMINATION 113.4 VENT TERMINAL CLEARANCES 123.5 VENT APPLICATION FLOW CHART 133.6 DEFINITIONS 133.7 ELBOW VENT LENGTH VALUES 143.8 TOP EXIT HORIZONTAL TERMINATION 143.9 REAR EXIT HORIZONTAL TERMINATION 163.10 TOP OR REAR EXIT VERTICAL TERMINATION 184.0 PRE-INSTALLATION PREPARATION 204.1 REMOVING THE VALVE ACCESS DOOR AND TOP DOOR TRIM 204.2 DOOR OPERATION 214.3 REAR EXIT 214.4 TOP VENT 215.0 INSTALLATION 225.1 WALL AND CEILING PROTECTION 225.2 HORIZONTAL INSTALLATION 235.3 VERTICAL INSTALLATION 235.4 USING FLEXIBLE VENT COMPONENTS 245.4.1 HORIZONTAL AIR TERMINAL INSTALLATION 245.4.2 VERTICAL AIR TERMINAL INSTALLATION 255.4.3 APPLIANCE VENT CONNECTION 265.5 USING RIGID VENT COMPONENTS 265.5.1 HORIZONTAL AIR TERMINAL INSTALLATION 265.5.2 EXTENDED HORIZONTAL AND CORNER TERMINAL INSTALLATION 265.5.3 VERTICAL AIR TERMINAL INSTALLATION 275.6 VERTICAL THROUGH EXISTING CHIMNEY 285.7 MOBILE HOME INSTALLATION 295.8 GAS INSTALLATION 295.9 OPTIONAL WALL SWITCH EXCLUDING BGD36CFG & GD36M 306.0 FRAMING 306.1 INSTALLING STAND-OFFS 316.2 MINIMUM FRAMING DIMENSIONS 326.2.1 STEEL HEADER INSTALLATION FOR CLEAN FACE SURROUND AND STYLO GLASS FACIA 336.3 MINIMUM ENCLOSURE CLEARANCES 346.3.1 REAR VENT ENCLOSURE 346.3.2 TOP VENT ENCLOSURE 356.3.3 ALCOVE ENCLOSURE 356.3.4 ENCLOSURE INSTALLATION WITH CLEAN FACE SURROUND OR STYLO GLASS FACIA (GD36M) 366.4 CLEAN FACE SURROUND FRAMING AND FINISHING EXCLUDING GD36M 376.4.1 FINISHED FLOOR INSTALLATION 376.4.2 HEARTH INSTALLATION 386.5 NON-COMBUSTIBLE FACING MATERIAL 386.6 ALCOVE FRAMING 396.8 REMOTE RECEIVER PLACEMENT 396.7 MINIMUM MANTEL CLEARANCES 397.0 FINISHING 407.1 DOOR INSTALLATION & REMOVAL 407.2 CLEAN FACE TRIM KIT INSTALLATION EXCLUDING GD36M 418.0 BGD36CF FINISHING 428.1 LOG PLACEMENT 428.2 GLOWING EMBERS 438.3 CHARCOAL EMBERS 438.4 LOGO PLACEMENT 438.5 OPTIONAL ROCK KIT 439.0 BGD36CFG / GD36M FINISHING 449.1 GLASS BURNER INSTALLATION 449.2 GD36M GLASS FRONT INSTALLATION / REMOVAL 459.3 TOP PRP PANEL INSTALLATION GD36M 4510.0 OPTIONAL BLOWER INSTALLATION 4610.1 ACCESSING THE BLOWER 4610.2 INSTALLING THE BLOWER SWITCH 4611.0 WIRING DIAGRAM 4711.1 BGD36CFG / GD36M LIGHT SWITCH 4711.2 BGD36CFG / GD36M BURNER SWITCH 48