Napoleon GDS60-1 Instructions Manual

Also see for CDVS600-1: Installation and Removal Instructions

Napoleon GDS60-1 Instructions Manual Manual pdf 1 page image

ELECTRONIC IGNITIONFUEL CONVERSION FOR MODELGDS60-1 / CDVS600-1INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOME OWNER.CHECK THE BOXES TO INDICATE THAT THE CORRESPONDING STEPS HAVE BEEN COMPLETED.WARNING: Failure to position the parts in accordancewith these diagrams or failure to use only partsspecifically approved with this appliance may result inproperty damage or personal injury.CAUTION: Before proceeding with conversion thegas supply must be shut off prior to disconnecting theelectrical power.1. Remove the cast front, glass viewing door and log set.Refer to the FINISHING section of your installation manual forinstructions.2. Remove the log support / burner assembly by removingthe two screws from the firebox back.3. Using a deep socket wrench, remove the main burnerorifice. A back-up wrench must be used on the manifold,located below the housing to ensure that the aluminum tubingdoes not twist or kink. For rear exit venting with horizontaltermination, use orifice described as rear vent. For top exitventing with either horizontal or vertical termination, use theorifice described as top vent. Replace the burner orificesupplied using pipe thread compound.4. Remove the pilot hood from the pilot assembly bypulling vertically. Use an allen key to unscrew the injector.Replace the pilot injector with the one supplied. Re-assemblethe pilot hood onto the assembly ensuring key position forproper alignment.5. Before replacing the burners,adjust the air shutters according tothe table on the back of this page.6. Replace and re-secure the logsupport/burner assembly ensuringthat the venturi fits over the burnerorifice.7. To convert the main valve to thedesired fuel, follow the instructionsthat are supplied with the SIT regulatorassembly kit.8. The conversion data label must be filled out andattached adjacent to the valve.9. Turn on the gas supply and check for gas leaks bybrushing on a soap and water solution.Do not use open flame.10. Re-install the log set. Then light the pilot and mainburner to ensure that the gas lines have been purged.11. Re-secure the glass viewing door. Turn on the electricalsupply to the appliance.Purge all gas lines with the glass door off.Assure that a continuous flow is at the burner before replacingthe door.Continued on reverseHOODPILOTORIFICEKit W175-0318, Natural Gas to Propane Includes;REGULATOR ASSEMBLY 1#55 BURNER ORIFICE - REAR VENT 1#53 BURNER ORIFICE - TOP VENT 1CONVERSION DATA LABEL 1PROPANE PILOT INJECTOR 1Kit W175-0319, Propane to Natural Gas Includes;REGULATOR ASSEMBLY 1#45 BURNER ORIFICE - REAR VENT 1#35 BURNER ORIFICE - TOP VENT 1CONVERSION DATA LABEL 1NATURAL GAS PILOT INJECTOR 1These kits are for use at altitudes of 0 to 4500 feet.LOG SUPPORTASSEMBLYSCREWSBURNERORIFICEPILOTASSEMBLYThis conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’sinstructions and all applicable codes and requirements of the authority having jurisdiction. If the informationin these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may resultcausing property damage, personal injury or loss of life. The qualified service agency is responsible forthe proper installation of this kit. The installation is not proper and complete until the operation of theconverted appliance is checked as specified in the owner instructions supplied with the kit.W415-0955 / A / 11.09.168PMG4UFFM-UE /BQPMFPO3E #BSSJF 0/-.($BOBEBt tGBY tXXXOBQPMFPOöSFQMBDFTDPN

/ 4

Related manuals for Napoleon CDVS600-1