Napoleon HYBRID 100 Installation And Operating Instructions Manual

Also see for HMF100: Installation and operating instructions

Napoleon HYBRID 100 Installation And Operating Instructions Manual Manual pdf 25 page image

W415-1066 / C / 06.22.1225DO NOT CONNECT THIs UNIT TO A CHIMNEY FLUE sERvINg ANOTHER AppLIANCE!!UsE CHIMNEY CERTIFIED TO 2100°F (1149°C) FOR wOOD BURNINg AppLIANCEs, LIsTED AsUL103HT(UsA), ULCs629(CANADA) MINIMUM 6” (152 mm) DIAMETER LIsTED REsIDENTIAL CHIM-NEY. sEE AND FOLLOw CHIMNEY MANUFACTUREs INsTRUCTIONs.CHIMNEY DRAFT gREATER THAN -0.06” w.C. (-15 pa) MAY CAUsE AN UNCONTROLLABLE FIREAND DAMAgE THE FURNACE.5.0 CLEArANCE TO COmBuSTIBLE mATErIALS/PLENum ANd vENTINg INSTALLATION5.1 FLuE / CHImNEyALL pLENUM DUCTINg AND vENTINg INsTALLATION MUsT CONFORM wITH CAN/CsA B365-01,AND NFpA 211. THE wARM AIR sUppLY DUCT sHALL BE CONsTRUCTED OF METAL IN ACCOR-DANCE wITH NFpA 90B, 2-1.1. pLENUM INsTALLED TO FURNACE sHALL BE CONTsTRUCTEDOF METAL IN ACCORDANCE wITH NFpA 90B, 2.1-3. ALwAYs CHECk LOCAL BUILDINg AND FIRECODEs, AND AUTHORITIEs HAvINg jURIsDICTION.ALL pLENUM, DUCTINg AND vENTINg MUsT BE INsTALLED BY A qUALIFIED/LICENsED INsTALL-ER.DO NOT UsE MAkEsHIFT COMpROMIsEs DURINg INsTALLATION. DO NOT BLOCk OR REsTRICTAIR. DO NOT IMpEDE AIR MOvEMENT IN zONEs MARkED "CLEARANCE TO COMBUsTIBLEs".MINIMUM CLEARANCE TO COMBUsTIBLE DIMENsIONs MUsT BE IMpLEMENTED.• use of inclined manual dampers are forbidden.• barometric dampers can be installed to maintain normal operating draft between 0.04” and0.06” W.C (10 pa and 15 pa).IF OpERATINg DRAFT RANgE Is ExCEEDED IT CAN CAUsE sOLID FUEL FIRE TO BURN OUT OFCONTROL CREATINg OvER FIRE CONDITION, sEE sECTION 7.1 RUN-AwAY FIRE OR CHIMNEYFIRE.sTRICTLY ADHERE TO ALL IDENTIFIED INsTALLATION CLEARANCEs.using a manometer with appropriate scale range connect testing tube between manometer andchimney connector. end of testing tube should be inserted in chimney connector so approximately1” (25 mm) of tube protrudes into and perpendicular to exhaust stream. this measurement shall betaken approximately 12” (305 mm) above elbow/t attached to the furnace flue. any hole made in thechimney connector for insertion of manometer tube shall be adequately sealed with high temp materi-als when testing is complete. Chimney draft to be a minimum -0.04” W.C. (-10 pa) to maximum -0.06”W.C. (-15 pa).5.1.1 CONTrOLLINg drAFT5.1.2 mEASurINg drAFT