Naxa NCA-681 Instruction Manual
Page 3 Page 12b) When pressed longer 2 seconds, it is activated as cyclical mode of followingfunctions for userās selection.->BEEP (ON/OFF) -> USER SET(FLAT/CLASSIC/ROCK/POP)->VOL(LAST/DEFA) ->CLK(ON/OFF)->CLK(12/24)mode.After selecting the desired mode, rotate the VOL knob to select one setupitem of the desired mode.BEEP ON/BEEP OFFBEEP ON mode: The beep is generated when any key is pressed.BEEP OFF mode: The beep sound is disabled.VOL LAST/VOL DEFAVOL LAST: The radio switches on at the actual volume it had when it was lastswitched off.VOL DEFA: After pressing SEL button, AVOL will be displayed. Then you canpre-select a constant switch-on volume by using the VOL knob.CLK ON/OFFCLK ON: Clock will always show on the display when power off.CLK OFF: Clock will disappear on the display when power off.3. POWER ON/OFFWhen the unit is power off, the unit comes to ON by pressing the power button.It also can turn on the unit to insert a disc into CD slot.When the unit is power on, press and hold the power button for more than 0.5seconds, the unit goes into power off mode.4. LCD Display5&6. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONSa) During RADIO mode:Press the >>| or |<< button shortly to manual tune up/down for the desiredradio station frequency step by step.Press and hold the >>| or |<< button for longer 0.5 seconds, to automaticallytune up/down for the radio station frequency of strong signal.b) During DISC playback mode:Press the >>| button briefly to play next track.Press the |<< button briefly to play the current track from the beginning of itif the playing time is more than 2 seconds.Press the |<< button briefly to play the previous track if the playing time isless than 2 seconds.Press the >>| or |<< button and hold to skip forwards or backwards, releaseto resume disc playback.7. BAND BUTTONDuring radio mode, press the BND button briefly to select the radio broadcastingband you would like to hear. The AM/FM band is toggled cyclically through thetuning bands: ->FM 1-> FM 2 -> FM 3 -> AM 1->AM 2 ->.8. MODE BUTTONPress the MD button to change among tuner(radio),disc(if disc is loaded)and AUX mode.TROUBLE SHOOTINGBefore using the check list please make all the connections first.If you still have questions after going through the checklist, please consultyour local customer service representative.Common SymptomsThere is no power.The CDs cannotbe loaded.CauseThe fuse has blown.Presence of CD disc inside the playerInserting the disc in upside downThe surface of CD is extremely dirtyor it is damaged.Temperature inside the car is toohigh.The volume control is set too low.There is no sound.The operation keysdo not workThe sound of theCD player skipsThe antenna cable is not connected. Insert the antenna cable firmly into theantenna socket of the device.No radio reception.1.The built-in microcomputer is notoperating properly due to noise2.Front panel is not properly fix intoits place1. Switch the device off and on again. Or pressthe RESET button to resume the program.2. Reinstall the front panelThe device has not been correctlyconnected.The installation angle is more than30 degreesWait until the road becomes smoother beforeplaying the CD.Adjust the installation angle to less than 30degreesTurn up the volume properly.Check the power and earth connectionaccording to the wiring diagram.Cool off until the ambient temperature returnsto normalClean the CD or try another CD, if this workscorrectly, the first CD is properly damaged.Insert the compact disc with the label facingupwardRemove the disc in the player then put a newupwardReplace another fuse according to the wiringdiagram.The car ignition is switched off. If the power supply is properly connected tothe car accessory, switch the ignition key toON or " ACC" " " .SolutionThe device doesnot work correctly(EJECT, LOAD,PLAY)In automatic searchmode the radio doesnot stop at a trans-mitting station.Tune in to a radio station manually.The transmission signals are tooweak.The CDs are loadedonly halfway intothe CD tray.The transport screws have not beenremoved.Remove the transport screws before using.The surface of the road is uneven.The surface of CD is extremely dirtyor it is damaged.Clean the CD or try another CD, if this workscorrectly, the first CD is properly damaged. |
Related manuals for Naxa NCA-681
Naxa NCA-683 Instruction Manual
Naxa NCA-670 Instruction Manual
Naxa NCA-602 Instruction Manual
Naxa NCA-696 Instruction Manual
Naxa NCA-613 Instruction Manual
Naxa NCA-671 Instruction Manual
Naxa NCA-692 Instruction Manual
Naxa NCA-611 Instruction Manual
Naxa NCA-600 Instruction Manual
Naxa NCA-699 Instruction Manual
manualsdatabase
Your AI-powered manual search engine