GEOM12 RIGGINGGEOM1210-I - GEOM1220-I Page 9 / 20GEOM12 RIGGINGAssemblyFrontPositioning 2x GEOM12-I. Connect both cabinets by inserting the axis through front holesand secure axis with brake nuts.BackAdjust the appropriate inter-angle value with the Linkbar and secure with the provided screws.Screws: 1 shoulder screw (D10x20), 2 washers (M10), 1 brake nut (M8).

WARNINGS

DESCRIPTION

PRESET GEOM12

GEOM12 RIGGING

GEOM12 – ACCESSORIES

ARRAY EQ

MAINTENANCE

spare parts

TECHNICAL SPECIFICATIONS

USER NOTES

Nexo GEOM1210-I User Manual

PLEASE READ CAREFULLY BEFORE PROCEEDING

INTRODUCTION

GEO M12 GENERAL SET-UP INSTRUCTIONS

MSUB18-I connectors

C ABLING

CONNECTION DIAGRAMS

3.5 MSUB18 / NXAMP4

NS-1 SIMULATION SOFTWARE

CONFIGURABLE DIRECTIVITY DEVICE

GEO M12 HARDWARE SETUP PROCEDURE

Ground Stacking Safety

Contacts

G ENERAL D ESCRIPTION 6.2.1 GEO M1210 and GEO M1220

GEO M12-I and MSUB18-I rigging systems

Warnings on GEO M12 & MSUB18 accessories

G ROUND S TACK SETUPS 6.3.1 Described configurations

GEO M12 only on Lightweight Bumper

GEO M12 only on Touring Bumper with stacking extensions

MSUB18 and GEO M12 with Ministack adaptor

MSUB18 and GEO M12 on Touring Bumper with stacking extensions

F LOWN CLUSTERS SETUPS

GEO M12 only flown with Lightweight Bumper

GEO M12 flown with Touring Bumper

MSUB18 flown with Touring Bumper

MSUB18 and GEO M12 flown with Touring Bumper

P ERMANENT I NSTALLATION VARIANT

T ESTING AND M AINTENANCE OF THE SYSTEM

SYSTEM CHECK ALIGNMENT GUIDELINES

D RIVING THE MSUB18 S FROM THE AUX SEND

GEO M1210 & GEO M1220

GEO M12 ACCESSORIES

VNI-BUMPM12

VNT-EXBARM12

VNT-GSTKM10M12L

VNT-GSTKM10M12S

VNT-MNSTKM12

GMT-LBUMPM12

GMT-EXBARM12L

GMT-FLGM12

MST-WBMSUB18

MST-DOLLYMSUB18

MST-COVMSUB18

MST-COV2MSUB18

GMT-2CASEM12

GMT-3CASEM12

VNT-LSTKM1018

GEO M12 & MSUB18 MODULES & ACCESSORIES LIST

GEO M12 Series

GEO M1210

GEO M1220

GEOM1210-I

GEOM1220-I


Contents Table Of Contents WARNINGS DESCRIPTION PRESET GEOM12 GEOM12 RIGGING GEOM12 – ACCESSORIES ARRAY EQ MAINTENANCE spare parts TECHNICAL SPECIFICATIONS USER NOTES	GEOM12 RIGGINGGEOM1210-I - GEOM1220-I Page 9 / 20GEOM12 RIGGINGAssemblyFrontPositioning 2x GEOM12-I. Connect both cabinets by inserting the axis through front holesand secure axis with brake nuts.BackAdjust the appropriate inter-angle value with the Linkbar and secure with the provided screws.Screws: 1 shoulder screw (D10x20), 2 washers (M10), 1 brake nut (M8). Previous Next / 20