NightBalance NB-SPT-PX Quick Manual
Quick manualFor ‘Pyxis’ Sleep Position Trainer NB-SPT-PX3 Use of the torso strapmanualquick manualCA BFD ESleep Position Trainer (SPT)Torso strapUSB-cableAdapterCD-ROM with SPT Connect SoftwareManual and quick manual1 Sleep Position TrainerColors of the indicator lightGreen SPT is ready for useOrange Recharge for next useRed See manual for troubleshootingConsult the manual for an overview of all colors ofthe indicator light.ON/OFF-button: Switch the SPT ON and OFF and toactivate additional functions.USB Port: Port to connect the USB-cable to rechargebattery and to read out data.2 Switching the SPT ON and OFF 4 Placing the SPT into the torso strap 5 Sleeping with the SPTCongratulations with your NightBalance Sleep Position Trainer!The NightBalance Sleep Position Trainer (SPT) is a new aid for the treatment of positional apnea.The SPT is a small and light device, which you can comfortably wear at the front of the chest with anergonomic torso strap. The SPT prevents supine sleep comfortably and effectively. The amount of sleepapnea attacks during the night decrease, improving you and your partner’s sleep. Better sleep makesyou feel more refreshed and improves your daytime performance.Switching On and OffOpen the rubber cover.Press the ON/OFF-button once to switch ON. Theindicator light turns on and shows either a green or anorange light.After use, switch the device OFF by holding the ON/OFF- button until the indicator light stops fl ashingwhite and then dims.Placement of the torso strapPlace the torso strap at the front of the torso, underthe chest above the upper abdomen. Ensure thatthe pocket opening faces upwards and the pocket iscentred on the torso.Pass the end of the torso strap through the buckle.Tightly fi t the torso strap around the body by closingthe torso strap using the buckle and Velcro.Sleeping with the SPTThe SPT uses a sleep-in period of 30 minutes, enablingyou to fall asleep in any desired position.From the third night, the SPT wills tart the training andwill remind you by soft vibration when you are lying onyour back. React to the vibrational feedback by turningto another position to prevent sleeping in the supineposition.Placing the device into the torso strapFollow the instructions on the sticker: place the SPTwith the arrow facing upwards.Place the SPT into the pocket. The grey backside of thedevice faces towards the body.Close the pocket sing the Velcro closure on the pocketfl ap.This manual is available in other languages on: www.nightbalance.com/download © 2012 NightBalance B.V. All rights reserved. Version: NB-SPT-QMN-PX-EN-1206The training program consists of 3 phases adapted to yourpersonal sleep behavior. The SPT will follow this programautomatically, you do not have to do this yourself. Use theonline webapplication to see where you are in the trainingand how you slept (see chapter 9.4 ‘Checking data: seeyour progress with your own eyes’).The three phases are:Diagnosis: The Sleep Position Trainer measures yoursupine sleep percentage. This phase lasts two nights.Start-up: During the next 7 days, the SPT willgradually decrease the number of times you areallowed to sleep on your back.. Training: After the start-up period, you will enter thetreatment (therapy) period. In this phase vibrationalfeedback is provided at all times when you lie on yourback.2h1hinsert CD-ROMstart software8 Read data using the computer9 Check your sleep data manuallyWhen connected with USB-Cable to electric circuitPress once to receive feedback on the correction of undesired sleep positionRead data with NightBalance SPT Connect softwarePlace the SPT Connect software installation CD-ROMin the computer or download the installation fi les on:http://www.nightbalance.com/softwareInstall the software.Start the software.Connect the SPT to your computer.Charge the SPTOpen the rubber cover.Insert the small plug of the USB-cable into the device.Plug the USB-cable into the adapter and thesockets.Or: Plug the USB-cable into the computer.Charging is completed when the indicator light stopsblinking and shows a continuous green light.Amount of vibrational feedbackOpen the rubber cover.Switch the SPT on, when it is not yet switched on.Press once on the ON/OFF-button.You will see a blinking blue indicator light. The numberof blinks indicates how often the SPT gave you vibrationalfeedback during the past night.Amount of times on the backOpen the rubber cover.Switch the SPT on, when it is not yet switched on.Press twice on the ON/OFF-button.You will see a blinking white indicator light. The numberof blinks indicates how often you slept on your backduring the past night.Safety warningsRead the instruction manual before using the product.Only use offi cial accessories provided by themanufacturer.Install the software before connecting the device tothe computer.Diagnosis Training Therapyphasefeedback %1 2 3 4 5 6 7 8 9 10 tot end of month0 %therapy day100 %Enabling the pause modeTurn the SPT together with the torso strap for 90°into an upright position to activate the pause mode.Hereafter can you turn the SPT back into the normalposition. The pausemode has been activated.The SPT will not give vibrational feedback when you lieon your back. After 20 minutes, the training programmwill resume automaticallyPackaging Contents7 Charge the SPTHow does the training program work?6 Pause modeWarningBefore connecting the SPT to the computer, you mustinstall the software. |
Related manuals for NightBalance NB-SPT-PX
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine