NightBalance Sleep Position Trainer Manual
Also see for Sleep Position Trainer: Manual
  |
EN NL DE FR IT DKManualSleep Position TrainerThe Sleep Position Trainer (SPT) by NightBalanceThe SPT is a small and light medical aid for the treatment of positional apnea. The SPT is worn aroundthe chest with a comfortable and ergonomic torso trap. It gently trains you by softly vibrating when yousleep on your back, reminding you subconsciously to switch to a different sleeping position. This wayapnea is prevented which helps you feel more refreshed and energetic during the day.Green SPT is ready for use.Orange Recharge before next use.Red Check website for troubleshooting:nightbalance.com/supportOn/off-button.Port for charger and USB cable.Indicator light.01 Press once to switch on the SPT.02 The indicator light (LED light) slowly blinksgreen when the SPT is switched on.01 SPT 02 Switch on 03 LED light90º 90º 90º01 Center the pocket on front of your torso,just below the chest.02 Pull the strap through the buckle and fasten with Velcro.03 Position the SPT with the arrow facing up andtowards you into the pocket.04 Close the pocket fl ap.04 Torso strap05 Sleeping with the SPTDuring sleep01 After the falling asleep period the SPT starts with vibrational feedback.02 The SPT adjusts the vibrational intensity to your sleeping behavior.03 Turn over from your back when the SPT vibrates.Pause mode01 Activate the 20-minute pausemode by turning the strap 90°for 5 seconds or by getting up.Falling asleep period01 Fall asleep in any position you prefer.02 The 30 minute falling asleep period starts onceyou switched the SPT on and you lay down.06 Reading out sleep dataNumber of vibrations during the past nightPress once and count the number of blue blinks.Make sure the SPT is switched on.Number of times on your supine during the past nightPress twice and count the number of white blinks.press 1x press 2x07 Switching off 08 ChargingholdPress and hold until the white light stopsblinking (3 blinks). Orange: Charge the SPT with the charger, or by connecting it to your computer with the USB cable.1,5 hours2 hoursstart softwareinsert USB-stickstart softwareinsert USB-stickstart softwareinsert USB-stickDayFeedback1 2 3 4 5 6 7 8 9 10 +01 Analyse fase 02 Build-up fase 03 Position training fase0 % 100 %C. SPT SoftwareA. SPT Comfort Program B. Auto-level adjustments01 Place the installation USB-stick or downloadthe SPT Software from the website:nightbalance.com/support/software02 Install and start the software. 03 Connect the SPT to your computer.Warning: Before connecting the SPT to thecomputer, you must install the software.The SPT automatically monitors yourresponsiveness to vibrations. The SPT adjuststhe intensity of the vibrations to suit yourresponsiveness.01 Analyse fase (night 1-2)No vibrational feedback, onlymeasures % of time slept onyour back.02 Build-up fase (night 3-9)Gradual build-up of vibrationalfeedback, decrease in % of timeslept on your back.03 Position training fase (night 10+)Vibrational feedback everytimeyou sleep on your back.The SPT Comfort Program consists of three fases.More information? www.nightbalance.comSee backside for more important information and other languages.D. Legend for LED light during useE. Legend for LED light during chargingGreen (slow blinking) Ready for use.Orange (slow blinking) The device needs to be charged for the next night.Red Go to nightbalance.com/support for troubleshooting.Blue (blinking) Number of vibrations during the past night.White (blinking) Number of times on your back during the past night.Green Fully charged and ready for use.Green (blinking) Charging, but ready for use.Orange (blinking) Charging, battery still low.Red Go to nightbalance.com/support for troubleshooting.Pink Warning: Do not disconnect the device from the computer. |
Related manuals for NightBalance Sleep Position Trainer
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine