NightStick XPP-5410G Instruction Manual
Also see for XPP-5410G: Instruction manualOperating instructionsOperating instructions
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5410G-15 09-15-2017Permissible XPP-5410 Flashlight AssemblyAPPROVAL No. 20-A140006-0TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLYWARNINGS:CLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 AEx ia IIC T3 GaCLASS I ZONE 0 Ex ia IIC T3 GaEx ia op is I MaEx ia op is IIC T3 GaIntertek ITS 13 ATEX27839XIECEx ITS 14.0036X-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell AAA Alkaline0359ID 4001184INTRINSICALLY SAFESECURITE INTRINSEQUEI M 1 Ex ia op is I MaII 1 G Ex ia op is IIC T3 GaThe Model XPP-5410 is MSHA approved for use with Energizer (Type E92),two Energizer (Type EN92), and Duracell (Type MX2400), Duracell(PC2400), and Duracell (EN92) batteries only. Replace the batteries infresh air only and replace all batteries at the same time. Do not mixbatteries from different manufacturers or of different types. The ModelXPP-5410 must not be opened in area where permissibility required.Conforms to:ANSI/UL STD 913, ANSI/UL60079-0, ANSI/UL 60079-11ANSI/ISA 60079-26Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25INMETROSegurançaNCCEx ia op is I MaEx ia op is IIC T3 Ga(-20ºC ≤ Tamb ≤ +40ºC)15.0319 XInstruction ManualXPP-5410GPlease read these instructions before using your Nightstick XPP-5410GIntrinsically Safe Penlight. They include important safety information andoperating instructions.THE XPP-5410G IS APPROVED FOR USEWARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable AAA batteries with thislight.y Warning: To prevent ignition of a hazardous atmosphere, do not openthe lens bezel in the hazardous environment. This task must ONLY beperformed in an area known to be non-hazardous.y Warning: When exchanging batteries, use only ENERGIZER E92, EN92,OR DURACELL MX2400, PC2400, EN92 BATTERIES.y Warning: To prevent ignition of a hazardous atmosphere, the AAA batteriesmust only be exchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new non-rechargeablebatteries witha used non-rechargeable batteries, or mix non-rechargeablebatteries from different manufacturers.y Warning: Substitution of components may impair intrinsic safety.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYy For personal safety, always confirm the rating of any known hazardous orpotentially hazardous location where the light is to be used.BATTERY INSTALLATIONWARNING: In order to maintain the XPP-5410G’s Intrinsically Safe rating,the only AAA batteries certified for use with this light are the ENERGIZERE92, EN92, OR DURACELL MX2400, PC2400, EN92 BATTERIES.y Do not attempt to use any other brand or model of AAA batteries withthis light.y Do not attempt to use any type of rechargeable AAA batteries withthis light.Warning: To prevent ignition of a hazardous atmosphere, do not removethe lens bezel in the hazardous environment. This task must ONLY bedone in an area known to be non-hazardous.y Loosen the locking screw located on the side of the lens bezel. NOTE:Do NOT attempt to completely remove the locking screw. Doing so is notnecessary and may damage the threads. The screw simply needs to beloosened enough to allow the lens bezel to unscrew.y Unscrew the lens bezel from the housing in a counter-clockwise direction.y Using 2 – AAA ENERGIZER E92, EN92, OR DURACELL MX2400,PC2400, EN92 BATTERIES (make sure both batteries are of the sametype), install the batteries in the light paying close attention to make surethat the positive end of the batteries point toward the bezel end of the light.y Replace the lens bezel by screwing it onto the housing in a clockwisedirection.y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so maydamage the threads and impact the light’s Intrinsic Safety.OPERATIONTHE XPP-5410G HAS TWO SEPARATE LIGHTING MODES:MOMENTARY FLASHLIGHT MODELightly press the tail switch for momentary operation. Release the switchto turn the light off.CONSTANT-ON FLASHLIGHT MODEPress the tail switch until it clicks and then release for constant-on mode.Press and release the tail switch again to turn the light off.WARRANTYLIMITED LIFETIME WARRANTYBayco Products, Inc. warrants this product to be free from defects inworkmanship and materials for the original purchaser’s lifetime. The LimitedLifetime Warranty includes the LEDs, housing and lenses. Rechargeablebatteries, chargers, switches, electronics and included accessories arewarranted for a period of two years with proof of purchase. Normal wear andfailures which are caused by accidents, misuse, abuse, faulty installation andlightning damage are excluded.We will repair or replace this product should we determine it to bedefective. This is the only warranty, expressed or implied, including anywarranty of merchantability or fitness for a particular purpose.For a complete copy of the warranty, go to www.nightstick.com/nightstick-product-support/warranties. Retain your receipt for proof of purchase. |
Related manuals for NightStick XPP-5410G
NightStick XPP-5410G Instruction Manual
NightStick XPP-5420G Instruction Manual
NightStick XPP-5412G Instruction Manual
NightStick XPP-5412G Instruction Manual
NightStick XPP-5418GX Instruction Manual
NightStick XPP-5418RX Instruction Manual
NightStick XPP-5414GX Instruction Manual
NightStick XPP-5418GX Instruction Manual
NightStick XPP-5411GX Instruction Manual
NightStick XPP-5418GX Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine