Niigata seiki WCDI-50D Instruction Manual
OPERATIONMeasure absolute dimension of workpieceABSOLUTE MODE (ABS)TROUBLESHOOTINGDIGITAL BORE GAUGE Instruction ManualModel No. WCDI-50D/WCDI-100D/WCDI-160D <combined>ABS/SETMIN CALZERO/ONABSOOABS/SETMIN CALZERO/ONOOABS/SETMIN CALZERO/ONABSOOABS/SETMIN CALZERO/ONABSOOEx. Rod NutEx. Rod60mmEx. Rod60mmWasher2mm Washer0.5mmWasher3mm Sub Rod55mmABS/SETMIN CALZERO/ONABSOOABS/SETMIN CALZERO/ONToMeasure:60mmToMeasure:62.5mmToMeasure:118mmEx. Rod 60mmNOTICEAUTO OFF DELAYINSERTING REPLACING BATTERYNOTICEASSEMBLYNiigata Seiki Co., Ltd.5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055Tel. : +81-256-33-5522 Fax. : +81-256-33-5518MAIL intl.sales@niigataseiki.co.jpURL http://www.niigataseiki.co.jpMEASUREMENTFor accurate measurements, follow the procedure described below.In cross section perpendicular to the axis of the bore, as shown in Figure 1, position the gauge along diameter . This is themaximum distance, and at this point the Indicator will read the maximum value. The Measurement Head will automatically move todiameter when inserted.In cross section parallel to the axis of the bore through diameter , position the indicator to minimize the distance . (Figure 2)In this position the Indicator will read the minimum value. This position must be manually determined by pivoting the Gauge asshown in Figure 3 while watching the Indicator to find the minimum value.Fig.1 Fig. 2 Fig. 3Before use, please make sure the Measurement Head components are not loose and tighten if necessary.Clean the Measurement Head and the ID of a Ring Gauge Standard using parts cleaner or cleaning solution.Press the [ZERO/ON] Button to turn on power. A long press to the [ZERO/ON] Button will turn power off.Turn on power. If the or symbols are displayed on the LCD, press the [MIN] Button to turn off.Adjust the SET value of the Bore Gauge to match the ID of the Ring Gauge Standard. Press and hold the [ABS/SET] Button untilSET blinks on the display.Continue holding the [ABS/SET] Button and the display character to the left will blink. Use a short press of the [ABS/SET] Button tochange the value, and a long press to change the character being modified. Repeat this process to enter the dimension of the RingGauge Standard on the LCD display. (Figure 4)When the value is entered the flashing position will return to SET . A shortpress of the [ABS/SET] Button to turn off the flashing.Insert the Measurement Head into the Ring Gauge Standard and press the[MIN] Button to put the Indicator into minimum-mode. Slowly pivot thegauge (Figure 3) to display the minimum value.Remove the gauge from the Ring Gauge and press the [CAL] Button untilOK is displayed.Preparation for measurement is now complete.Put the gauge into the workpiece to be measured, and pivot the gaugeslowly. (Figure 3) The LCD will display the measured value. (Figure 5)Press the [ON/ZERO] Button momentarily to reset display in preparationto measure the next workpiece.Turn on power. If or symbols are displayed on the LCD,press the [MIN] Button to turn off. If ABS is displayed press the[ABS/SET] Button to turn off.Insert the Measurement Head into the Ring Gauge Standard and press[MIN] Button to put the Indicator into minimum-mode. Slowly pivot thegauge (Figure 3) to display the minimum value.Remove the gauge from the Ring Gauge and press the [CAL] Button untilOK is displayed.Preparation for measurement is now complete.Put the gauge into the workpiece to be measured, and pivot the gaugeslowly. (Figure 3) The LCD will display the difference between themeasured workpiece and the calibration standard. (Figure 6)Press the [ON/ZERO] Button momentarily to reset display in preparationto measure the next workpiece.Difference between workpiece and referenceCOMPARATIVE MEASUREMENTSERROR CORRECTIVE ACTION If problem persists, or if you have anyquestions, please contact distributor.Please note, manufacturer is unable torespond to inquires or provide servicedirectly. Please contact distributor.LCD does not displayDisplayed value is unstableDisplay is not clearCycle power by removing andreplacing battery.Replace battery with new one.Fig.4Fig. 5Fig.6Set to matchWorkpiece I.D. valueDiff. between Work-piece and ReferenceRing GaugeStandardWork-pieceWork-pieceThank you for purchasing the Digital Bore Gauge.Please read this manual thoroughly before use for proper operation.Extension RodHandleShaftProbe Tip0.5mm 1mm 2mm 3mmWashersGuide12Cap1 Not Used2 "0.01" indicates theresolution of the display'sdigital bar graph. The bargraph display will changewith each 0.01mm changein the measured value.AccessoriesSub Rod 55mmWCDI-160D onlyLoosen the Clamp Screw and insert the DigitalIndicator into the gauge body. Tighten the ClampScrew to secure.After attaching, press the [ZERO/ON] Button on theDigital Indicator to turn on power. Confirm that thedisplayed reading changes by gently squeezing themeasurement head. If necessary, adjust the depththat the Digital Indicator is inserted into the gaugebody.Select the combination of Sub Rod (WCD-160only) Extension Rod and Washers for thedimension you want to measure.Remove the Rod Adj. Nut put on the desired Sub Rod, Rod, and Washers,and secure with the Extension Rod Mounting Nut.Please select combination with fewest number of Washers.Extension RodsWCDI-50D 35 40 45 50mm piecesWCDI-100D 50 55 60 65 70 75 80 85 90 95 100mm 11 piecesWCDI-160D 50 55 60 65 70 75 80 85 90 95 100 105mm 12 piecesSub Rod 55mm x WCDI-160D onlyWasher 0.5 1 2 3mm (1 each size)Battery CR2032Lithium button cell, 1x (for test)ACCESSORIESNot including quantization error ( 1 count)SPECIFICATIONSWCDI - 50D3 5 - 5 01551. 2WCDI - 100D WCDI - 160D5 0 - 10 00.0020.002 0.00218633 31. 60 6 . 05 0 - 16 01861. 64 5 0 475 5 7 0PART IDENTIFICATION Including supplied Digital GaugeExamplesMeasuring RangeResolutionWide range accuracyAdjacent errorRepeatabilitySingle Stroke RangeAuto Off DelayWeightModel No.Length below Handle:150mmMountingNutExtensionRodClampScrew[MIN]Button[ABS/SET]ButtonLCD Display[ZERO/ON]Button[CAL] Button[CAL] ButtonGauge(Digital Indicator)MeasurementHeadThis is a precision instrument, handle with care.Do not disassemble or modify.Keep instrument away from water and oil.Use only with supplied Extension Rods and Washer.Keep instrument away from direct sunlight and high temperatures such as ina car, or near a stove or heat source.After use, remove any dirt or cutting chips and apply rust preventative oil toExtension Rod and Washer. When not in use store in supplied storage case.This product is for measuring inside diameter; use only as directed. Improperuse may cause accident or injury.Avoid using in high electric fields, such as near fluorescent lights or switchingpower supplies. Electrical interference may cause incorrect readings.Press and hold the [ZERO/ON] Button to turnpower OFF.Press and hold [ABS/SET] and [ZERO/ON]Buttons at the same time.When ----- is displayed, release the[ZERO/ON] Button, then release the[ABS/SET] Button in that sequence.The Auto Off Delay time will be displayed. Press[ABS/SET] to change.Each press of the [ABS/SET] Button will changethe delay by 1/2 hr. (30 min.) from 0 to 6 hr.Press [ZERO/ON] when done and display willreturn to the measurement screen.Once set, the delay time is saved even when poweris OFF.Use only CR2032 typelithium button cell.Pull out the case fromthe two side edges toremove. Insert batterywith (+) side facingdown. BatteryCaseBatteryCR2032INSERTClampScrew |
Related manuals for Niigata seiki WCDI-100D
Niigata seiki WCDI-50 Instruction Manual
Niigata seiki WCDI-10D Instruction Manual
Niigata seiki WCDI-6 Instruction Manual
Niigata seiki WCDI-35 Instruction Manual
Niigata seiki WCDI-6D Instruction Manual
Niigata seiki WCDI-35D Instruction Manual
Niigata seiki CDI-50 Instruction Manual
Niigata seiki N-5AS Instruction Manual
Niigata seiki CDI-18D Instruction Manual
Niigata seiki VH-30D Instruction Manual
manualsdatabase
Your AI-powered manual search engine