Ninja BL680A Owner's Manual
Also see for BL680A: Owner's guide
           | |
15 16www.ninjakitchen.com1-877-646- 5288PROBLEMS POSSIBLE REASONS & SOLUTIONSMotor Doesn’t Start or BladeAssembly Doesn’t Rotate.Make sure the container is securely locked on the motor base.Make sure the lid is securely on the container in the correct position (alignarrows).The appliance is turned “Off”. Press the power button ( ) to turn “On”.Check that the plug is securely inserted into the electrical outlet.Check the fuse or circuit breaker.The unit has overloaded. The appliance will stop and the power light willflash. Unplug and wait approximately 15 minutes before using again.The unit has overheated. Unplug and wait approximately 15 minutes beforeusing again.Check to make sure the unit is not overloaded.Food is Unevenly Chopped. Either you are chopping too much food at one time, or the pieces are not ofeven size and processing smaller amounts per batch.Food is Chopped Too Fine or isToo Watery.The food has been over processed. Use Auto-iQ™ Pulse button forcontrolled processing.Food Collects On Lid or On theSides of the Container. The mixture is too thick. Add more liquid.You Cannot Achieve SnowFrom Solid Ice.Do not use ice that has been sitting out or has started to melt. Use icestraight from the freezer.Start with a few pulses and then go to a continuous blending cycle.Motor Base Won’t Stick toCounter or Table Top.Make sure surface and suction feet are wiped clean. Suction feet will onlystick to smooth surfaces. Suction feet WILL NOT stick on some surfacessuch as, wood, tile and non-polished finishes.DO NOT attempt to use appliance when the motor base is stuck to asurface that is not secure, (cutting board, platter, plates, etc.).You get an “Err” MessageYour Ninja® is able to detect which jar is on the base. You may be tryingto use a program that is not designed for the jar you have installed. Theprograms will light up indicating which programs are available for each jar.You have a blinking red lightThe unit is not installed properly. For your safety the unit will only be able tobe turned on when it is properly assembled. Please refer to the assemblypages of this inspiration guide for assistance.Troubleshooting GuideReplacement PartsORDERING REPLACEMENT PARTSTo order additional parts and attachments, please visit our website: www.ninjakitchen.comor feel free to contact customer service: 1-877-646-5288.HOW TO CLEANCAUTION: Make sure that the motor base isunplugged from the power source before insertingor removing any blade assembly and beforecleaning.CAUTION: DO NOT immerse the motor base intowater or any other liquid.1 Separate/remove all parts from each other.2 Hand Washing: Wash the lids, pitcher, food processorbowl, Nutri Ninja® cup, and blade assemblies in warm,soapy water. When washing the blade assemblies, usea dish-washing utensil with a handle to avoid directhand contact with blades. Handle blade assemblieswith care to avoid contact with sharp edges. Rinse andair dry thoroughly.Dishwasher: The containers, lids, blade assembliesand attachments are all dishwasher safe. The lidsand blade assemblies are top rack dishwasher safe.Ensure that the blade assemblies are removed from thecontainers before placing in the dishwasher.WARNING: Handle the Blade Assemblies withcare when washing, as the blades are sharp.Contact with the blades’ edges can result inlaceration.3 Wipe the motor base clean with a damp cloth.Please call customer service if any servicing needs to beperformed on the appliance at 1-877-646-5288.Care & MaintenanceHOW TO STORE1 Store the Nutri Ninja® | Ninja® Blender System withAuto-iQ™ Technology upright with the blade assemblyinside the corresponding container with the lid securedon top. Do not place anything on top. Store the rest ofthe attachments in a safe place where they will not bedamaged and won’t cause harm. Wrap the power cordaround the cord wrap on the back of the motor base.RESETTING THE MOTOR THERMOSTATThe Nutri Ninja | Ninja Blender System with Auto-iQTechnology features a unique safety system whichprevents damage to the unit’s motor and drive systemshould you inadvertently overload your appliance. Ifthe appliance is being overloaded, the motorwill stop. Allow the appliance to cool forapproximately 15 minutes. To reset the appliance,follow the resetting procedure below:1 Unplug the appliance from the electrical outlet.2 Remove and empty the container and ensure that nofood is jamming the Blade Assembly or attachments.3 Allow the appliance to cool for approximately 15minutes.4 Re-install the container onto the base and re-plug theappliance into the electrical outlet.5 Proceed to use the appliance as before making sure notto exceed the recommended maximum capacities. |
Related manuals for Ninja BL680A
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine