Nissin Di466 Instruction Manual
Also see for Di466: Instruction manual
      | |
Contents | 
Switch Di466 Four Thirds on and while the ready lamp is on, press the modeselect button to select S1(color turns Green) or S2(color turns Blue). The modeselect button turns to TTL(nolight)—Manual(red)—S1(green)—S2(blue) andback to TTL.Setting slave flash Di466 Four Thirds:When flash is set to either slave mode, the first lamp ofFlash power level indication lamps is lighten. Thislamp shows the 1/32 manual power level. Press theFlash power level select button at marked + to selectdifferent power of 1/161/81/41/2 and Full.Press the button at marked — to power downward.The power you selected is memorized and remainsunchanged untill the unit is switched off.Set slave flash at any place and direct the flashhead as you desire. Slave sensor may not respondto the master flash in the extremely bright conditionor under the poor sensing situation.Use the flash stand included. Place Di466 Four Thirds on to the flash standwhich can be placed either on the flat place or on the tripod by the screw.NOTE Metal type accessory shoe is not recommended since it may give electric damageon the electrical contact of the flash hotshoe.GreenBlueTo reset the flash unit to the other mode, press the mode select button forTTL and or Manual mode.Energy saving system for stand-by modewill not work when it's in slave mode.Automatic shut off function is howevereffect. It automatically turns-off when notin use over 60 minutes.The zoom setting position is automaticallyset for the focal length of 12mm whileusing Di466 Four Thirds as a slave unit.TTL exposure level is accurately calibrated for standard balance inaccordance with Nissin’s standard. If any adjustment is however required,or if you like to set your preferable level, it can be adjusted for about±0.75 (3/4)ev. This adjustment can only be set when the flash is off.Insert the battery magazine with 4 batteries fully loaded as instructedabove.Press the pilot lamp and On/Off switch bothtogether and hold for 3 seconds. The modeselect lamp turns purple showing the unit isready for TTL exposure level adjustment.TTL Exposure level custom settingSet the camera for flash shooting mode. Point the subject and shoot.The slave flash will synchronize to the master flash and gives additionallighting from the different direction you desired.Shooting the subject:Purple Press togetherPlace the master flash on the camera and switch it on. Or set the camera forflash mode to always fire the built-in flash.Setting master flash:Press the power level select button either + or- to adjust it to the required exposure level.Each LED shows 0.25(1/4)ev incrementsand it can be adjusted up to+0.75(3/4)ev.(over exposure efficiency), ordown to -0.75(3/4)ev.(under exposureefficiency). Press the On/Off switch for 3sec. to turn the unit off. The adjusted level ismemorized and kept as customized defaultTTL exposure level. This setting is permanentlykept until you alter the setting to the otherrequired level. Start to use flash unit from“Turn on the flash unit” at “BASICOPERATION” explained as above.Come to Stand-by mode in 2 minutes, andPower off in 30 minutes after the power onor the last use of flash unit.Four Thirds and Micro Four Thirds systemdigital camerasAutomatic exposureManual exposure at 6 power level(See guide number table below)33 / 108 at 53 mm focal length (ISO 100 m/ft)12 - 53 mm (9 mm with diffuse panel)(Automatically set for the lens focal length)4 x size AA batteries(Size AA Ni-MH or lithium batteries usable)200-1500 flashes according to the mode(with alkaline batteries)4 seconds with fresh alkaline batteriesEffective range of approx. 0.7 to 6m / 2.3 to 20 ft.5600 K1/800 (full power flash) sec.1/800-1/20,000 (controlled flash) secondsSlave function with 6 power level(See guide number table below)67(W) x 105(H) x 95(D) mm / 2.6(W) x 4.1(H) x 3.7(D) inches230 gTTLSpecificationsUsable camerasGuide No.IlluminationcoveragePower sourceBattery lifeEnergy savingRecycle timeFlash exposureAF assist lightColor temperatureFlash durationWirless flashDimensionsWeightGuide No. at manual exposure mode (ISO 100 in meters/feet)Install batteries to correct direction.ZoomingPositionFlash Power LevelGuide Number tableTrouble ShootingThe flash unit does not start charging.Batteries are not correctly installedMount the flash unit firmly on the camera's hot shoe.The flash unit does not fire.The flash unit is not firmly clipped on the cameraReplace the batteries if the recycle timeBatteries are exhausted>>>>>>>>>Use manual exposure flash or an appropriatecorrection by the TTL exposure level custom setting.The flash picture is overexposed or underexposed.A reflective object or strong lighting near the subject>>>Set to TTL mode or other power level.The unit is set for manual exposure mode>>>Turn on the switch again.The flash unit is automatically powered off>>>12mm14mm18mm25mm35mm43mm53mm18/5920/6522/7224/7927/8830/9833/10812.7/4220/6522/7224/7927/8830/9833/108Full 1/2 1/4 1/8 1/16 1/329/2910/3311/3612.7/4213.5/4415/4916.5/546.4/217/237.8/2610/3311/369/299.5/314.5/155/165.5/187/238/266.4/296.7/313.2/103.5/124/135/165.6/184.5/154.7/15.5 |
Related manuals for Nissin Di466
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine