Norgren 18D-LTx2 Operating Instructions Manual
               | |
with instructions and supervision from aspecialist.Specialists are capable of assessing thework assigned to them, recognising possiblehazards and implementing the appropriatesafety measures based on their professionaltraining, knowledge and experience, as wellas their knowledge of the relevant specifi-cations. The specialist must comply with theregulations relevant to the specific area.Warnings in these instructionsThese instructions include warnings besideprocedural instructions for procedures withrisk of personal injury or property damage.The described hazard prevention measuresare to be observed.Signal wordCAUTIONIndicates a potentially dangerous situationwhich can lead to property damage if notavoided.WARNINGIndicates a potential hazard which can lead tosevere injuries or death if not avoided.You must observe the followingGeneral information• Please pay attention to the regulations for safety,accident prevention and environmental protection inthe country of use and at the workplace.• The 18D-LT x2 must not be modified nor converted.Failure to comply with these instructions as well aschanges to the unit negate any liability on the partof the manufacturer; the warranty for the unit andaccessories is voided.• Use the 18D-LT x2 only within the performancerange specified in the technical data.• All configuration of the 18D-LT x2, all installation,dismantling and startup work must be performedonly by trained, qualified personnel.• Do not disconnect cables and hoses on systemswhich carry live voltage or are under pressure!• Do not subject the pressure switch to bending, tor-sion or shock.• Pressure measurement on the 18D-LT x2 onlyworks correctly if suitable connection cables areused.For installation and startup• The warranty applies only to the the configurationdelivered. It is void if the installation is not correct.• Always ensure that the relevant part of the systemdoes not carry live voltage and is not underpressure before the 18D-LT x2 is installed orremoved.• Ensure that the connected compressed air lines donot contain dirt particles and that no liquids enterthe device along the connected lines.• Use only threaded inserts which seal to the outside(maximum screw-in depth 9 mm).• Do not install units with obvious damage andreplace defective units promptly.®®Norgren GmbH, Werk FellbachStuttgarter Strasse 12070736 Fellbach, GermanyTel: +49 711 5209-0Fax: 07 11 / 52 09-614The data specified above only serve to describe theproduct. No statements concerning a certain conditionor suitability for a certain application can be derived fromour information. The given information does not releasethe user from the obligation of exercising judgement andverification. It must be remembered that our products aresubject to a natural process of wear and ageing.© This document, as well as the data, specifications andother information presented in it are the sole propertyof Norgren GmbH. It may not be reproduced or given tothird parties without their consent.Subject to change without notice.Printed in GermanyThese instructions were originally written in German.Order no: 7503568.99.08.2010DE/EN/FR/IT/ES/Bedienungsanleitung • Operating instructions • Moded’emploi • Istruzioni d’uso • Instrucciones de servicio •BruksanvisningPRESSURE SWITCH18D-LT x27503568.99.08.2010Version: ADE/EN/FR/IT/ESEnglish1 About these instructionsThese instructions contain important infor-mation required for safe and proper instal-lation, operation, maintenance and simplerepair of the 18D-LT x2 pressure switch.X Read these instructions and especially theSection 2 ‘For your safety’ before installing the18D-LT x2 and connecting it to the compressedair supply.Standards followed:We hereby declare that this product com-plies with the following standards or norma-tivedocuments:• EMC as per 2004/108/EC• Emitted interference EN 61000-6-3 (2007)• Interference resistance EN 61000-6-2 (2005)Other applicable documents• Technical data and dimensions according to themain catalogue2 For your safetyThe 18D-LT x2 has been manufacturedaccording to current technical standards andrecognisedsafety-related regulations. Nonetheless,failure to comply with the general safetyinstructions, warnings before procedures inthese instructions could result in personalinjury and property damage.X Therefore you should read these instructionsthoroughly before working with the 18D-LT x2.X Keep the instructions available to all users atany time.X Always provide third parties with these operatinginstructions together with the 18D-LT x2.Intended useX Use the 18D-LT x2 only for monitoring pressurevalues in accordance withX the technical specifications in industrial environ-mentsX Adhere to the performance limits indicated in thespecifications (see data sheet 5.11.006). Inten-ded use includes having read and understoodthese instructions andX and especially the section ‘For your safety’.Non-intended useNon-intended use includesusing the 18D-LT x2• for areas of application not listed in these instruc-tions,• under operating conditions other than thosedescribed in these instructions.Qualification of personnelExhaust guard installation, removal andstartup require basic electrical and pneu-matic knowledge as well as familiarity withthe respective special terminology. Instal-lation, removal, startup and operation musttherefore only be performed by a electricianor pneumatics specialist or a trained person08/10 Subject to change without notice / Page 1 7503568.99 |
Related manuals for Norgren 18D-LTx2
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine