Manuals database logo
manualsdatabase
Your AI-powered manual search engine

North Star 10 kW Installation Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Contents
  1. FCC Statement 2
  2. feedback from you
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Preface 7
  7. Introduction to the Northstar radar 9
  8. Warranty 3
  9. kw radar system overview
  10. install the radar
  11. power boat installations
  12. How to find the optimum height for the scanner
  13. How to find the maximum detection range
  14. How to reduce false echoes and shadow zones
  15. kW radar dimensions
  16. Install the 25 kW scanner unit
  17. Install the radar processor
  18. Wire the radar system
  19. kW radar processor connectors
  20. Run the interconnection cable (NS003105/NS003106) to the radar processor
  21. Earth the 25 kW scanner
  22. Install the 25 kW open array
  23. Connect the 25 kW radar processor to a 6000i or 6100i display
  24. Connect the radar communications cable (NS003107) to the junction box
  25. Configure the remote power control for a 6000i or 6100i (common power source)
  26. Configure the remote power control for a 6000i or 6100i (different power sources)
  27. Connect the 25 kW radar processor to an 8000i display
  28. Configure the remote power control for an 8000i
  29. Connect the power cable
  30. Radar system checklist
  31. Set up the radar with the Northstar 6000i or 6100i
  32. Configure the navigator communications
  33. Calibrating the radar
  34. Set the trigger delay
  35. Set the heading calibration (heading sensor not installed)
  36. Restore all the factory settings
  37. Maintenance
  38. Troubleshoot the radar
  39. If the scanner fails to turn
  40. Make sure the power is present and correctly wired
  41. Manual tuning procedure for the 6000i or 6100i system
  42. kW radar system specifications
North Star 10 kW Installation Manual Manual pdf 29 page image
12.6 Install the 25 kW open arrayIMPORTANT: Install the open array onto the scanner ONLY after you've connected the 25 kWinterconnection cable.Use the assembly sheet provided and check that you've got all the components shown. Follow theinstructions on the assembly sheet to install the open array.Northstar 25 kW Radar Installation Manual 29
/ 53
This manual is suitable for:
10 kW25 kW
Manuals database logo
manualsdatabase
Your AI-powered manual search engine