Notifier 002-439 Installing

Notifier 002-439 Installing Manual pdf 1 page image

CCProceed as follows:1 Using an appropriate-sized screwdriver, remove (and discard) the threeM3 screws (position A) that secure the cover (B) to the back box (C), thenlift off, remove and retain the cover.2 Find a suitable location to install the enclosure, then use the dimensionsbelow to measure the mounting hole positions. Using a suitable-sizeddrilling bit for holes to take 6mm (#12) screws, drill the holes and fit wallplugs, then secure the back box to the wall with three 6mm (#12) screws.Open the knock-outs as required and remove any swarf.3 Connect the back box to earth at the safety earth point (D).4 Use one of the M4 SEMS (E) to connect the earth lead (F) to the back box.Proceed as follows:Using an appropriate-sized screwdriver, remove (and discard) the threeM3 screws (position A) that secure the cover (B) to the back box (C), thenlift off, remove and retain the cover.Find a suitable location to install the enclosure, then use the dimensionsbelow to measure the mounting hole positions. Using a suitable-sizeddrilling bit for holes to take 6mm (#12) screws, drill the holes and fit wallplugs, then secure the back box to the wall with three 6mm (#12) screws.Open the knock-outs as required and remove any swarf.Connect the back box to earth at the safety earth point (D).Use one of the M4 SEMS (E) to connect the earth lead (F) to the back box.1234Check Your Equipment....Check Your Equipment....The Multi-Mount Enclosure (PN: 002-439) is very simple to fit to a wall providing the instructions described below arefollowed. The Enclosure is capable of housing: one CMX-10RM or MMX-10M or MCX-55 module, or up to two MRM,MMX, CMX, ZMX or ISO-X modules, or one MULTI-MX module, or one IM-10 or CR-6 or SC-6 or CZ-6 module, or oneSerial NION Board. The Enclosure is secured to a wall using three 6mm (#12) screws.The Multi-Mount Enclosure (PN: 002-439) is very simple to fit to a wall providing the instructions described below arefollowed. The Enclosure is capable of housing: one CMX-10RM or MMX-10M or MCX-55 module, up to two MRM,MMX, CMX, ZMX or ISO-X modules, one MULTI-MX module, one IM-10 or CR-6 or SC-6 or CZ-6 module, oneSerial NION Board. The Enclosure is secured to a wall using three 6mm (#12) screws.oror or orTaking suitable precautions, before proceeding with the installation, removeall packaging and inspect for any damage that may have occurred duringtransit. If no damage is evident, proceed using the instructions below. In theunlikely event that damage has occurred, DO NOT PROCEED, contact yoursupplier and refer to the panel Installation & Commissioning Manual.Observing all necessary precautions, proceed with the installation of theMulti-Mount Enclosure.Taking suitable precautions, before proceeding with the installation, removeall packaging and inspect for any damage that may have occurred duringtransit. If no damage is evident, proceed using the instructions below. In theunlikely event that damage has occurred, DO NOT PROCEED, contact yoursupplier and refer to the panel Installation & Commissioning Manual.Observing all necessary precautions, proceed with the installation of theMulti-Mount Enclosure.Fitting the Multi-Mount EnclosureFitting the Multi-Mount EnclosureOBSERVE PRECAUTIONSFOR HANDLINGELECTROSTATICSENSITIVEDEVICESOBSERVE PRECAUTIONSFOR HANDLINGELECTROSTATICSENSITIVEDEVICESATTENTIONATTENTIONCCProceed as follows:1 Using an appropriate-sized screwdriver, remove (and discard) the threeM3 screws (position A) that secure the cover (B) to the back box (C), thenlift off, remove and retain the cover.2 Find a suitable location to install the enclosure, then use the dimensionsbelow to measure the mounting hole positions. Using a suitable-sizeddrilling bit for holes to take 6mm (#12) screws, drill the holes and fit wallplugs, then secure the back box to the wall with three 6mm (#12) screws.Open the knock-outs as required and remove any swarf.3 Connect the back box to earth at the safety earth point (D).4 Use one of the M4 SEMS (E) to connect the earth lead (F) to the back box.Proceed as follows:Using an appropriate-sized screwdriver, remove (and discard) the threeM3 screws (position A) that secure the cover (B) to the back box (C), thenlift off, remove and retain the cover.Find a suitable location to install the enclosure, then use the dimensionsbelow to measure the mounting hole positions. Using a suitable-sizeddrilling bit for holes to take 6mm (#12) screws, drill the holes and fit wallplugs, then secure the back box to the wall with three 6mm (#12) screws.Open the knock-outs as required and remove any swarf.Connect the back box to earth at the safety earth point (D).Use one of the M4 SEMS (E) to connect the earth lead (F) to the back box.1234Check Your Equipment....Check Your Equipment....The Multi-Mount Enclosure (PN: 002-439) is very simple to fit to a wall providing the instructions described below arefollowed. The Enclosure is capable of housing: one CMX-10RM or MMX-10M or MCX-55 module, or up to two MRM,MMX, CMX, ZMX or ISO-X modules, or one MULTI-MX module, or one IM-10 or CR-6 or SC-6 or CZ-6 module, or oneSerial NION Board. The Enclosure is secured to a wall using three 6mm (#12) screws.The Multi-Mount Enclosure (PN: 002-439) is very simple to fit to a wall providing the instructions described below arefollowed. The Enclosure is capable of housing: one CMX-10RM or MMX-10M or MCX-55 module, up to two MRM,MMX, CMX, ZMX or ISO-X modules, one MULTI-MX module, one IM-10 or CR-6 or SC-6 or CZ-6 module, oneSerial NION Board. The Enclosure is secured to a wall using three 6mm (#12) screws.oror or orTaking suitable precautions, before proceeding with the installation, removeall packaging and inspect for any damage that may have occurred duringtransit. If no damage is evident, proceed using the instructions below. In theunlikely event that damage has occurred, DO NOT PROCEED, contact yoursupplier and refer to the panel Installation & Commissioning Manual.Observing all necessary precautions, proceed with the installation of theMulti-Mount Enclosure.Taking suitable precautions, before proceeding with the installation, removeall packaging and inspect for any damage that may have occurred duringtransit. If no damage is evident, proceed using the instructions below. In theunlikely event that damage has occurred, DO NOT PROCEED, contact yoursupplier and refer to the panel Installation & Commissioning Manual.Observing all necessary precautions, proceed with the installation of theMulti-Mount Enclosure.Fitting the Multi-Mount EnclosureFitting the Multi-Mount EnclosureOBSERVE PRECAUTIONSFOR HANDLINGELECTROSTATICSENSITIVEDEVICESOBSERVE PRECAUTIONSFOR HANDLINGELECTROSTATICSENSITIVEDEVICESATTENTIONATTENTIONYour kit should contain:Multi-Mount Enclosure PN: 002-439Allen key 2mm PN: 334-051M3 x 10 SEM screws (5 off) PN: 775-058M4 x 8 SEM screws (9 off) PN: 776-042M3 x 20mm nylon spacers (5 off) PN: 423-252M4 x 45mm nylon spacers (8 off) PN: 423-311M3 x 6 button-hd. hex. black steel screws (8 off) PN: 775-059M3 nylon washers (8 off) PN: 790-019Cable assembly (earth) 225mm M4 blade/ring PN: 082-160 -005Your kit should contain:Multi-Mount Enclosure PN: 002-439Allen key 2mm PN: 334-051M3 x 10 SEM screws (5 off) PN: 775-058M4 x 8 SEM screws (9 off) PN: 776-042M3 x 20mm nylon spacers (5 off) PN: 423-252M4 x 45mm nylon spacers (8 off) PN: 423-311M3 x 6 button-hd. hex. black steel screws (8 off) PN: 775-059M3 nylon washers (8 off) PN: 790-019Cable assembly (earth) 225mm M4 blade/ring PN: 082-160 -005140.3140.3170.6170.6280.6280.655554545130130225225997-286, Issue 3 January 2003Installing the Multi-Mount EnclosureInstalling the Multi-Mount Enclosure1AABBAA AADD11 2233FFEE44

/ 2

Related manuals for Notifier 002-439