NuTone E662E Installation Instructions Manual

Also see for E662E: Specification sheet

Contents

NuTone E662E Installation Instructions Manual Manual pdf 10 page image

11. OPERATIONA. BLOWER OFF D ELAY TOUCH PAD:When a speed is selected, touch the delay touch pad to activate the delay function. The corresponding speed indicatorLED will start flashing to indicate this function is activated. Touch once for a 5-minute delay, twice for 10-minute delay,three times for 15-minute delay and four times for a 20-minute delay. The fan will continue to operate for theprogrammed minutes and will stop automatically. To cancel the delay function, wait 2 seconds and touch the delaytouch pad once again; the blower will then work in normal mode.NOTE: The blower speed can be increased - or decreased - during delay mode without starting another delay cycle.B. ON / B LOWER SPEED CONTROL TOUCH PAD:Touch this touch pad to turn on the blower at the last selected speed. To change the blower speed, touch the touch padagain until the desired speed is obtained.NOTES: 1. Each time you touch on the speed control touch pad, the speed changes by increments of 1 (e.g.: speed1 to speed 2, to speed 3, and then speed 4. From the fourth speed, goes down to speed 1).2. The last speed used is kept in memory except the fourth, the next time the blower will be turned on, it willrun on speed 3.C. OFF B LOWER TOUCH PAD:Touch this touch pad to turn off the blower.This command also cancels the delay function (if activated).D. OFF L IGHTING TOUCH PAD:Touch this touch pad to turn off lighting.E. HALOGEN LIGHT TOUCH PAD:Touch this touch pad to turn on the halogen lamps. The lighting intensity changes by increments of 1 (e.g.: Touch once for lowintensity, once again to get more, up to three times. From the higher intensity, touch once to go back to the lower intensity).NOTE: The last lighting intensity used is kept in memory. The next time the halogen lamps will be turned on, they willlight with the last intensity used.F. NIGHTLIGHT / KEYBOARD LOCK TOUCH PAD:Touch this touch pad to activate the nightlight. The LED will light to indicate the nightlight is on.When cleaning the hood, use the keyboard lock. To activate the keyboard lock, touch on this touch pad during 3 seconds;the LED will flash to indicate the keyboard lock is on. Touch on the touch pad and hold for 3 seconds again to stop thekeyboard lock function.NOTES: 1. When cleaning the hood, never spray cleaning agent directly on the controls; spray it on the cleaningcloth and wipe the control with it. Spraying cleaning agent directly on the control will causeunexpected keyboard activation.2. When the keyboard lock is on, it stops the HEAT SENTRY.3. If there a temporary power failure when the keyboard lock is on, when the power will be restored, thekeyboard lock will still be on.A) Blower OFF Delay touch padD) OFF lighting touch padB) ON / Blower speed touch padE) Halogen light touch padC) OFF Blower touch padF) Nightlight / keyboard lock touch padHC0017 A B C D E FAlways turn your blower on before you begin cooking to establish an air flow in the kitchen. Allow the blower run for afew minutes to clear the air after you turn off the range.HEAT SENTRYThis hood is equipped with a Heat Sentry thermostat. This thermostat is a device that will turn on or speed up the blowerif it senses excessive heat above the cooking surface.1) If blower is OFF - it turns blower ON to HIGH speed.2) If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.When HEAT SENTRY is activated, the first and the last speed blower LEDs are flashing alternately.When the temperature level drops to normal, the blower will return to its original setting.WARNINGThe HEAT SENTRY can start the blower even if the hood is turned OFF. In this case, it is impossible toturn the blower OFF with blower switch. If you must stop the blower, do it from the main electrical panel.!- 7 -