Nuvo NV-LRC1 User Manual
Also see for NV-LRC1: Installation manual
                        | |
6. If the device responds, go to step 6. If the device does not respond,press CH+. The remote will try the next code. Continue until the deviceresponds.NOTE: Press CH- to try the previous code.7. To set the code, press SETUP once. The LED blinks twice.8. To search for other device codes, repeat steps 1 to 6.Checking The CodesIf you have set up the remote using the procedure in “Searching For YourCode”, you may need to find out which five-digit code is operating yourequipment.For example, to find out which code is assigned to your TV:1. Press SOURCE 1 once.2. Press and hold SETUP until the red LED blinks twice, then release.3. Enter 990. The LED blinks twice.4. To view the code for the first digit, press numeric key 1. Count the LEDblinks (for example, three blinks = 3), and write down the number inthe appropriate code listing in step 8 under “Programming a Device”.NOTE: If a code digit is 0, the LED does not blink.5. Repeat step 4 for the four remaining digits, using 2 for the seconddigit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifthdigit.6. To check for other device codes, repeat steps 1-5, substitutingSources 2-6.Changing Volume LockThe NV-LRC1 comes preset to allow independent volume control of eachselected device (Global Volume Unlock). However, you may change theVolume Lock setting to Global Volume Lock so that one source’s volumewill control volume in all other modes. After that, you can performIndividual Volume Unlock on a selected source to set its volume controlfor independent operation or Global Volume Unlock to remove all volumelocking.Locking Volume Control to One Mode (Global Volume Lock)1. Press and hold SETUP until red LED blinks twice, then release.2. Enter 993 and then press the mode key for the source you want tocontrol volume (for example, CD). The LED blinks twice. Now, whenyou press VOL+, VOL- or Mute, the selected source (for example, CD)will control the volume regardless of the current mode.Unlocking All Volume Control (Restoring Global Unlock)1. Press and hold SETUP until the red LED blinks twice, then release.2. Enter 993 and then press VOL+. The LED blinks four times. Volume isindependently controlled for all programmed sources.Unlocking a Single Source’s Volume Control1. Press a source key (1-6).2. Press and hold SETUP until the red LED blinks twice, then release.3. Enter 993 and then press VOL-. The LED blinks four times. Volume isindependently controlled for the selected sources.Programming MacrosA macro can be used to control a home theater operation, to set afavorite channel, or for other multiple functions you would like tocontrol with one key press. You can use any key to activate a macro.Moreover, each Macro Key can hold up to 32 key presses total.You can program a macro that will operate regardless of what mode youare in, or one that will only operate when you are in a specific mode.NOTE: Programming a new macro over an existing one will erase theoriginal macro.Programming a Mode-Independent Macro1. Press and hold SETUP until the red LED blinks twice, then release.2. Press 995. The LED blinks twice.3. Press the key you want to use to activate your macro (POWER, anyunused key, etc.).4. Enter the series of commands you want the macro to execute (up to 32commands).5.Press and hold SETUP until the red LED blinks twice, then release.Now, when you press the Macro key, the remote will send the series ofcommands you have entered, regardless of what mode you are in. Forexample, you could program the Macro key to turn on both your TV andcable box and select a particular channel.To clear the macro, repeat steps 1 to 5 above, but do not enter a series ofcommands at step 4.Programming a Mode-Dependent Macro1. Press a source key (1-6).2. Press and hold SETUP until the red LED blinks twice.3. Press 978. The LED blinks twice.4. Press the key you want to use to activate your macro (POWER, anyunused key, etc.).5. Enter the series of commands you want the macro to execute (up to 32commands).6. Press and hold SETUP until the red LED blinks twice, then release.3Directly enter channels(For example, 09 or 31).Press ENTER to send channelnumber entries on some TVmodels.Macro device keys can be used todedicate multiple string macrocommands.Whole-Home Control is dedicatedcontrol of your NuVo System.MUTE, VOL-, VOL+, ON/OFFduplicate the NuVo zone keypadfunctions.Press this key... To...Programming a DeviceTo control devices, 1-6, follow these steps.Before proceeding, find the codes for the devices you want to program in“Manufacturer’s Codes” in the following pages and write them down orhighlight them.NOTE: Any device may be set up on any mode key.2M1Whole-Home Control1. Turn on the device (for example, CD player) and, if needed, loadmedia (for example, a CD).2. Press a device key (1-6).3. Press and hold SETUP until the red LED blinks twice, then release.4. Enter the first five-digit code for your device. The red LED blinks onceas each digit is entered. If the code is correct, the LED blinks twice.NOTE: If the LED does not blink twice, repeat steps 2 to 4 and try enteringthe code again.5. Aim the remote at the device and press POWER. The device shouldturn off. If it does not, repeat steps 3 to 5, trying each code for yourbrand until you find one that works. If you cannot find a code thatworks, see “Searching For Your Code”.6. Repeat steps 1 to 5 for the other devices you want to control. ForFuture reference, write down each working device code below:Searching For Your CodeIf your device does not respond to the remote after trying all codeslisted for your brand, or if your brand is not listed, try searching for yourcode:1. Press a device key once.2. Press and hold SETUP until the red LED blinks twice, then release.3. Enter 991. The LED blinks twice.4. Enter the device group number:5. Select a test function, such as POWER or PLAY. The remote sends IRcodes from its library to the selected device, starting with the mostpopular code first.SOURCE 1 Code:Desc. _______SOURCE 2 Code:Desc. _______SOURCE 3 Code:Desc. _______SOURCE 4 Code:Desc. _______SOURCE 5 Code:Desc. _______SOURCE 6 Code:Desc. _______TV (TVs)VCR (VCRs, DVD players)0 Cable (Cable Converters, Video Accessories, SatelliteReceivers).12Audio (Audio Amplifiers, Audio Amp/Tuners, CD players)Code Device GroupM2 M3 M4M5 M6 M7 M8MUTE VOL- VOL+ ON/OFF3 |
Related manuals for Nuvo NV-LRC1
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine