1Installation GuideNetwork CameraModel No. BB-HCM515A (PoE Ready)Please read the included Important Information before proceeding.Complete Operating Instructions and all other documentation can be found on the included CD-ROM.• This document (Installation Guide) explains how to physically connect the camera to the power supply and network, as well how to mount or place thecamera for regular use.• The Setup Guide describes how to set up the camera so that it can be accessed using a PC.• Refer to the Operating Instructions on the CD-ROM for details regarding the camera’s features.• Refer to the Troubleshooting Guide on the CD-ROM if you have any problems configuring or using the camera.Abbreviations• UPnP is the abbreviation for “Universal Plug and Play”.• The Network Camera is referred to as “the camera” in this document.• The Setup CD-ROM is referred to as “the CD-ROM” in this document.Installation Procedure OverviewThe following is an overview of the steps required to install and setup the camera. All steps are explained in this document unless otherwise noted.Preparation1. Confirm the following items are included in the camera’s packaging.• Additional pieces can be ordered by calling 1-800-332-5368.2. You will need the following additional items to install and configure the camera.– a PC (see the system requirements in the Important Information document)– a LAN cable (CAT-5 straight cable)– a routerOptionYou can also connect the camera using the optional Panasonic BB-HCA3A AC Adaptor.The BB-HCA3A includes the following items.Camera DiagramPreparationConfirm that you have allthe items required forinstallation.Camera DiagramMake sure you know thenames of the camera’sphysical features.ConnectionsConnecting the camera toyour network and to thepower outlet.SetupSetting up the camera (described in the includedSetup Guide). This involves configuring thecamera so that it can be accessed from a PC.MountingMounting or placing thecamera.Main Unit (1 pc.) Washer S (1 pc.)Order No. XWG4F16VWUsed when securing the safetywire to the camera.Screw A (1 pc.)Order No. PQHV2610PJ65Used for connecting the safety wire to thecamera.Flexible Stand (1 pc.)Order No. PQKL10082Z1Washer L (1 pc.)Order No. XWG26D12VWUsed when securing the safetywire to the ceiling or wall.Screw B (4 pcs.)Order No. XTB4+20AFJUsed for mounting the camera.Safety Wire (1 pc.)Order No. PQME10080ZUsed to secure the camerawhen mounting it.Important Information (1 pc.)Installation Guide (thisdocument) (1 pc.)Setup Guide (1 pc.)Setup CD-ROM (1 pc.)Order No. PQQX15704ZCDContains the Setup Program needed toconfigure the camera, as well as the camera’sdocumentation.**See the included Important Information for a description ofeach document.AC Adaptor (1 pc.)Cord Length: About 3 m (9 feet 10 inches)AC Cord (1 pc.)Cord Length: About 1.8 m (5 feet 11 inches)Front View Side and BottomViewRear ViewABCDLens coverLensMicrophoneIndicator*1EFGHIFACTORY DEFAULTRESET buttonSD memory card slotRESTART buttonFUNCTIONbutton/indicatorStand/tripod mountingholeJKLMNOPQRSStand mounting holeSerial number andMAC address labelAC adaptor cord/videocable hookSpeaker/microphonecable hookLAN portDC INExternal I/O interfaceVIDEO OUT terminalAUDIO OUT terminalMIC terminal*1 See 1.1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD-ROM for indicator meaning.ABCDEFGHIJKLMNO P Q R S© 2006 Panasonic Communications Co., Ltd. All Rights Reserved.PQQX15708YA KK1106MH1107Please read this document before using the product, and save this document for futurereference. Panasonic Network Camera Website: http://www.panasonic.com/netcamfor customers in the USA and Puerto RicoIndoor Use Only