Panasonic C9701U Operating Instructions Manual

Contents

Panasonic C9701U Operating Instructions Manual Manual pdf 7 page image

CQ-C9901U/C9801U/C9701UEnglish1312PreparationCQ-C9901U/C9801U/C9701UNote: Adjust the clock when “ADJUST” appears on thedisplay.1 Press [MENU] to display the menu dis-play.For using the remote control, hold down [MENU]for 2 sec. or more.2 Press []] or [[] to display the DIS-PLAY menu.3 Press [{] to select “CLOCK ADJ”.4 Press [BAND] (SET) to confirm the dis-play.5 Adjust the setting value.[[]: Adjusting minutes[]]: Adjusting hours[}]: Forward[{]: Backward6 Press [BAND] (SET) to confirm theadjustment.7 Press [MENU].For using the remote control, hold down [MENU]for 2 sec. or more.When the power is switched on for the first time, ademonstration message appears on the display. Press[DISP] to change to regular mode.1 Set your car’s ignition switch to the ACCor ON position.The demonstration screen appears.Example: CQ-C9901U2 Press [DISP] (Display).The demonstration screen is cancelled, and no moreappears.Note: If you would like to turn on the power and makethe demonstration message appear, hold down [SRC](PWR: Power) for 4 sec. or more after turning off thepower in other than the XM mode.You may need to set the following depending on thedevices to be connected.Using Subwoofer¡ Subwoofer level adjustment (a page 36)¡ Subwoofer low pass filter (a page 36)Connecting an XM Direct TM receiverPreparation:¡ Connect the optional XM Direct TM receiver ( XMD1000 ).¡ To connect the XM DirectTM receiver (XMD1000), it isrequired to use an optional extension cord (XMDPAN100)that is produced by XM exclusively for Panasonic prod-ucts.Getting StartedIt is required to sign up to become an XM Satellite Radiosubscriber. After checking your XM Satellite Radio ID,sign up on the XM’s website or by calling them.1 Check of XM Satellite Radio ID¡ Write down the ID indicated on the lower right ofyour XM DirectTM receiver (XMD1000).¡ Check the ID shown by tuning your XM Radio tochannel 0. (a page 30)2 Activate the XM Satellite RadioSelect either of the below to sign up.¡ Web site: http://www.xmradio.com/activation¡ Phone number: 1-800-XM-RADIO (96-72346)Note: Refer to the operating instructions for the XMDirect TM receiver for details.Connecting an AV device (TV, VTR)If you connect TV to AUX1 terminal, set the AUX1 settingto TV.1 Press [SRC] (Source) to select theAUX1 mode. (a page 16)2 Press [MENU] to display the menu dis-play.For using the remote control, hold down [MENU]for 2 sec. or more.3 Press [BAND] (SET) to adjust.: TV: Other devices (Default)Note: When using an external TV unit manufactured bya third party, select the TV mode.4 Press [MENU] to confirm the adjust-ment.The following functions are activated when the SecurityFunction is ON. (a page 38)¡ The security indicator blinks when removing the faceplate.¡ The alarm sounds and the message appears on thescreen to warn you to remove the face plate at poweroff.Security IndicatorSRC CSPreparationFirst Time Power On(DEMONSTRATION)Remote Control PreparationSecurity FunctionSettingOther SettingsClock adjustment(CLOCK ADJ)Battery ReplacementPreparation Before Initial UsePull the insulation film outfrom the backside ofremote control gently.Warning¡Keep batteries and insulation film out of reach ofinfants. If an infant ingests a battery, please seekimmediate medical attention.Caution¡ Remove and dispose of an old battery immediately.¡ Do not disassemble, heat or short a battery. Donot throw a battery into a fire or water.¡ Follow local regulations when disposing of abattery.¡Improper use of a battery may cause overheat-ing, an explosion or ignition, resulting in injuryor a fire.Note:¡Battery Information:Battery Type: Panasonic lithium battery (CR2025)(Included in the remote control)Battery Life: Approximately 6 months under nor-mal use (at room temperature)qwq Remove the battery holderwith the remote control unitplaced on a flat surface.q Stick your thumbnail intothe groove, and push theholder in the direction ofthe arrow, and at thesame time.w Pull it out in the directionof the arrow using atough pointed object.w Put a battery in the case with(+) side facing up.e Put the case back.23Tough pointed objectBack sideInsulation film