Panasonic C9801W Operating Instructions Manual

Contents

20 CQ-C9901W/C9801W 21 EnglishCQ-C9901W/C9801WIn the AM mode, only NOISE SUPPRESSION and LOCALcan be selected.1 Press [MENU] todisplay the menudisplay.For using the remotecontrol, hold down[MENU] for 2 sec. ormore.2 Press [}] or [{] to select a mode to beadjusted.3 Press [BAND](SET) to adjust.4 Press [MENU] to confirm the adjust-ment.For using the remote control, hold down [MENU]for 2 sec. or more.MONO (Monaural)Noise reduction when the signal strength decreases: Receiving in stereo (default): Receiving in mono and reducing the noise levelLOCALSetting when searching for a station: Searching even for a relatively low-intensityradio wave station (default): Searching only for a high-intensity radio wavestationNOISE SUPPRESSIONIF filter setting for noise suppression: Wide range: Middle range (default): Narrow rangeAUTO PRESETYou can select 6 or 18 stations for FM presetting with theuse of APM.:Presets 6 stations to FM1 to FM3 respectively, that is, 18stations in total at the same time. This function is usefulfor presetting more than 6 stations. (default):Presets 6 stations with good reception to the selectedband from FM1 to FM3. This function is useful for preset-ting stations in different areas in different bands.PRESET EDITYou can arrange the order of the preset stations. Presetstations can be reordered as you like after executing APMor the like.1 Press [}], [{], []] or [[] to select onestation to be interchanged.2 Press [BAND] to confirm your selection.3 Press [}], [{], []] or [[] to select theother station to be interchanged.4 Press [BAND] to confirm your selection.●Calling an FM station registered on D·MRADIO AUDIO FILTERYou can select the reception status (band) of FM stationsregistered on D·M.: Off (default): High cut level 1: High cut level 2 (same processing at receivingan FM station)Mono/Local Setting (Radio Menu Display)(MONO/LOCAL)RadioRadioUp to 6 stations can be preset in AM, FM1, FM2, and FM3respectively.Preset stations can be simply called up by pressing [}](P·SET) or [{] (P·SET).Notes:¡ Direct Access can be executed with [1] to [6] buttonson remote control.¡ You can switch between 6 and 18 for FM presettingstations. (a page 21)¡ Preset stations are changeable. (a page 21)Auto Preset Memory (APM)Stations with good receiving conditions are automaticallypreset.1 Select a band.2 Hold down [BAND](APM) for 2 sec.or more.The preset stations under best receiving conditionsare received for 5 sec. each after presetting the sta-tions (SCAN). To stop scanning, press [}] or [{].Note: New stations overwrite existing saved stations.Manual station preset1 Tune in to a station.2 Hold down [}] or [{] for 2 sec. ormore.3 Select a preset number by pressing [}]or [{].4 Preset the station by holding down [}]or [{] for 2 sec. or more.Frequency/preset number blinks once.Notes:¡ New stations overwrite existing saved stations.¡ In step 2, a station can be registered by holding downthe numeric button [1] to [6] for 2 sec. or more.¡ To stop presetting stations, press [DISP] (Display).Station Preset(APM: AUTO PRESET MEMORY, P·SET: PRESET)Direct Memory(D·M: DIRECT MEMORY)You can assign your favorite broadcasting station to the[D·M] button. As the result of doing that, your favoritebroadcasting station can be received even if the CD modeor the CD changer mode is activated.(Default: FM 87.50 MHz)Note: For the use of an FM transmitter, it is usefulfor users to register applicable frequencies on D·M(Direct Memory).D·M station calling1 Press [D·M: DIRECT MEMORY].D·M station writing1 Select a station you would like to preset.2 Hold down [D·M: DIRECT MEMORY]for 2 sec. or more. Lights when the D·M mode is activated.SRC CS