Panasonic CQ-RD243N Operating Instructions Manual

Also see for CQ-RD243N: Service manual

Contents

Panasonic CQ-RD243N Operating Instructions Manual Manual pdf 10 page image

16ENGLISH19CQ-RD243N15ENGLISHCQ-RD243N18AB A4:A5:A8:A7:A5 A7 A8 A4A5*:B7B8B5B6B3B4B1B2B7:B8:B5:B6:B3:B4:B1:B2:(Green)(Green w/black stripe)(White)(White w/black stripe)(Gray)(Gray w/black stripe)(Violet)(Violet w/black stripe)(Red)(Black)(Blue w/white stripe)(Yellow)(Blue w/white stripe)Extension Cord(DIN/BATT/RCA/GND) (Black)CD Changer (Option)CX-DP880N Ground LeadTo a clean, bare metallicpart of the carchassis(Yellow)Fuse (3A)Battery LeadTo the car battery,continuous+12V DCSupplied for anoptional CD Changer. Cassette ReceiverCQ-RD243NePower andSpeakerConnectorAntennaISO AntennaConversion Cord(Option)(If needed)(L)(White)(L)(White)(R)(Red)CD ChangerInput ConnectorPre-Amp.OutConnector(Rear)DIN CordRCA CordRCA Cord (R)(Red)CD ChangerControl ConnectorBATTERY 15AACCCautions:¡Check the connectors provided on your car (see precaution below) before connecting the system.¡This unit is designed for use in a car having a 12-volt negative ground battery system.¡To prevent damage to the unit, be sure to follow the connection diagram.¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords).¡Do not insert the power connector into the unit until the wiring is completed.¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and preventcable terminals from touching any metal parts.Electrical ConnectionsIf the fuse (rear panel) blows frequently, theymay be something wrong with the unit.Consult your nearest Panasonic ServiceCentre for service.¡This unit can be connected to anoptional CD changer (CX-DP880N,CX-DP9061/DP9060EN, CX-DP88N, CX-DP801/DP803EN orCX-DP601EN) and optional exten-sion cord.¡For details consult your nearestauthorized Panasonic Dealer.¡For connection to a CD changer,refer to the operating instructionsof the CD changer (CX-DP880N,CX-DP9061/DP9060EN, CX-DP88N, CX-DP801/DP803EN orCX-DP601EN).Fuse (15 A)To remove the FusePrecautions (ISO Connector)¡The pin arrangement of the power connectorconforms to ISO standard.¡The pin arrangement of ISO connectors in somecars may differ from the ISO standard.¡Please check that the pin arrangement of theconnector in your car conforms to ISO standard.¡For car types A and B, change the wiring of thered and yellow leads as shown at below.¡After connection, insulate the portions marked(C) with insulating tape.Note: For cars other than types A and B, pleaseconsult your local car shop.CCBATTERY 15AACCISO Standard ISOCCBATTERY 15AACCA Car Type AACCCCB Car Type BBATTERY 15AA7: IGN or ACC switched 12 V supply(Red)(Yellow) (Yellow)(Red)(Red)(Yellow) (Yellow)(Red)(Red)(Yellow) (Red)(Yellow)A4: IGN or ACC switched 12 V supplyA4: +12 V Battery (Permanent supply)A7: +12 V Battery (Permanent supply)A7: +12 V Battery (Permanent supply)A4: No connectionA7A41FuseePower andSpeakerConnector32Note: The power antenna extends automatically whenthe power of this unit is turned on.A5 : Motor Antenna Relay Control Lead(Blue w/white stripe)To Motor Antenna (Max. 500mA)This lead is not intended for use with a switch actuatedpower antenna.A7 : Power Lead (ACC or IGN) (Red)To ACC power, +12 V DC.A8 : Ground Lead (Black)To a clean, bare metallic part of the car chassis.A4 : Battery Lead (Yellow)To the car battery, continuous +12 V DC.C1 : External Mute Lead(Orange) (not used)C3 : External Remote Control Lead(Brown w/black stripe)When using a non-Panasonic external remote control, referto the manufacture for their product before connecting.A5*: This lead can be used as either Amp.Relay Control Power Lead or Motor Antenna Relay Control Lead, or both at thesame time. However, the current capacity of this lead is 500 mA.Left (+)Left (–)Left (+)Left (–)Right (+)Right (–)Right (+)Right (–)RearFrontFrontRearISO ConnectorSpeakers

/ 13

Related manuals for Panasonic CQ-RD243N