Panasonic CS-A12CTP Service Manual

Also see for CS-A12CTP: Brochure Operating instructions Operating instructions Operating instructions Technical information

NAME OF EACH PART Remote Control Remote Control Signal.• Make sure it is not obstructed.• Maximum distance : 10 m.• Signal received sound.One short beep or one long beep. Notes for Remote Control.• Do not throw or drop.• Do not get it wet.• Certain type of fluorescent lamps may affectsignal reception. Consult your dealer. Do not place the remote control in a location exposedto direct sunlight, or next to a heating unit, or otherheat source. How to Insert the Batteries1 Gently press the place marked OPEN and slidethe cover towards you.2 Insert the batteries– Be sure the direction is correct. About the batteries• Can be used for approximately one year. Observe the following when replacing the batteries• Replace with new batteries of the same type.• Do not use rechargeable batteries (Ni-Cd).• Remove the batteries if the unit is not going to beused for a long period. Proper way to operate the remote control in thecase of ceiling/wall mounting.• Operate the remote control in parallel with the floor.(See the figure below)1 Signal Transmitter2 Operation Display3 Room Temperature Setting Button(Illuminating button)4 Operation Mode Selection Button5 Sleep Mode Operation Button(Illuminating button)6 Timer Setting Button7 Timer Selection Button8 OFF/ON Button(Illuminating button)9 Fan Speed Selection Button0 Auto Airflow Direction Button! Timer Set/Cancel Button@ Manual Airflow Direction Selection Button# Reset Point(Press with fine-tipped object to clear the memory)Cooling ModelHeat Pump ModelHH• The signal changes as shown in the figure below.It means that the receiving conditions are bad andthe signal can not be controlled properly.O.K.OUT(Fig. 2)(Fig. 1) Horizontal LevelHOW TO OPERATE To start the operation• Press 1.• POWER indicator (green) on the indoor unit will light up.• To stop, press once more. Setting Mode• Press 2 to select:-Cooling ModelAUTO – Automatic OperationCOOL – Cooling OperationDRY – Soft Dry OperationFAN – Air Circulation OperationHeat Pump ModelAUTO – Automatic OperationHEAT – Heating OperationCOOL – Cooling OperationDRY – Soft Dry OperationPREPARATION BEFORE OPERATION Indoor Unit1 Connect the power supply cord to an independentpower supply. Setting Temperature• Press 3 to increase or decrease the temperature.• The temperature can be set between 16°C ~ 30°C• Recommended temperature:• During AUTO Operation, press 3 to select:-• Operation with 2°C higher than the standardtemperature.• Operation with the standard temperature.• Operation with 2°C lower than the standardtemperature. Standard TemperatureCooling Model• Once the Automatic Operation is selected, the indoortemperature sensor operates automatically to selectthe desired operation mode with Cooling or Soft Dry.• After the operation mode has been selected, themode does not change.Heat Pump Model• At the beginning of the automatic operation, Heating,Cooling or Soft Dry is automatically selected accordingto the indoor temperature.• After the operation mode has been selected, themode does not change.OperationCoolingSoft DryStandardtemperature25°C22°CIndoortemperature23°COperationCoolingSoft DryHeatingStandardtemperature25°C22°C21°CIndoortemperature23°C20°CCooling ModelCOOL –> 26°C ~ 28°CDRY –> 1°C ~ 2°Clower than theroom temperatureHeat Pump ModelCOOL –> 26°C ~ 28°CDRY –> 1°C ~ 2°Clower than theroom temperatureHEAT –> 20°C ~ 24°C Operation DetailsCOOL – Cooling Operation• To set the room temperature at your preferencecooling comfort.AUTO – Automatic Operation• Sense indoor temperature to select the optimummode.• Temperature is not displayed on the remote controlduring AUTO operation.DRY – Soft Dry Operation• A very gentle Cooling Operation, prior todehumidification. It does not lower the roomtemperature.• During Soft Dry operation, the indoor fan operates atLow Fan Speed.HEAT – Heating Operation(for Heat Pump Model only)• Heat is obtained from outdoor air to warm up theroom. When the outdoor ambient air temperaturefalls, the heating capacity of the unit might bereduced.• Defrosting OperationDepend on the outdoor temperature, the operationoccasionally stops to melt the frost on the outdoorunit.FAN – Air Circulation Operation(for Cooling Model only)• Heated air rises and collects at the top of the room.The air circulation circulates the heated air downward,thus increasing heating effectiveness. When the unitis installed floor mounted, you should set thetemperature higher than that of ceiling mounted.At ceiling mounted At floor mounted136CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5