NAME OF EACH PART■ Remote Control● Remote Control Signal.• Make sure it is not obstructed.• Maximum distance : 10 m.• Signal received sound.One short beep or one long beep.● Notes for Remote Control.• Do not throw or drop.• Do not get it wet.• Certain type of fluorescent lamps may affectsignal reception. Consult your dealer.CHECKTEMPAUTOONOFFAUTUTO DRDRY FANANCOOLCOOLFANAUTORESET CLOCKMODE SLEEPECONOMYFAN SPEEDAIR SWINGOFF CANCELON SET1 2 3TIMEROFF/ONPOWERFULAUTO MANUAL#!$%^$*&35879064(21HEAHEAT● How to Insert the Batteries1 Slide down the remote control cover completely2 Insert the batteries– Be sure the direction is correct– 12.00 at display - flashing• Set the current time (CLOCK) immediately toprevent battery exhaustion.● About the batteries• Can be used for approximately one year.● Observe the following when replacing thebatteries• Replace with new batteries of the same type.• Do not use rechargeable batteries (Ni-Cd).• Remove the batteries if the unit is not going to beused for a long period.1 Signal Transmitter2 Operation Display3 Powerful Mode Operation Button4 Room Temperature Setting Button(self-illuminating button)5 Operation Mode Selection Button6 Economy Mode Operation Button7 Auto Airflow Direction Button8 ON-Timer Button9 OFF-Timer Button0 Reset Point(Press with fine-tipped object to clear the memory)! OFF/ON Button(self-illuminating button)@ Sleep Mode Operation Button# Fan Speed Selection Button$ Manual Airflow Direction Selection Button% Timer Set Button^ Timer Cancellation Button& Time-Setting Button* Clock Button( Remote Control CoverCHECKAUTOOFAUTO HEAT DRY FANCOOLFANAUTOAUTORESET CLOCKAIR SWINGOFFCANCEL123TIMERPOWERFULAUTO MANUALECONOMYSLEONSETFAN SPEEDMODE211.5V1.5VPREPARATION BEFORE OPERATION■ Indoor Unit1 Connect the power supply cord to an independentpower supply2 Open the front panel3 Remove the air filters4 Fit the air purifying filters in place5 Insert the air filters6 Close the front panel■ Remote Control– To set the current time1 Press 1.2 Then press 2 to increase or decrease the time.3 Press 1 again.Set time at display will light up.CHECKAUTOAUTO HEAT DRY FANCOOLFANAUTORESET CLOCKFAN SPEEDAIR SWINGOFF CANCELON SET1 2 3TIMERAUTO MANUAL1262 1453■ Setting Temperature• Press 3 to increase or decrease the temperature.• The temperature can be set between 16°C ~ 30°C.• Recommended temperature:• During AUTO Operation, press 3 to select:-• Operation with 2°C higher than the standardtemperature.• Operation with the standard temperature.• Operation with 2°C lower than the standardtemperature.● Standard TemperatureCooling Model• Once the Automatic Operation is selected, the indoortemperature sensor operates automatically to selectthe desired operation mode with Cooling or Soft Dry.• After the operation mode has been selected, themode does not change.Heat Pump Model• At the beginning of the automatic operation, Heating,Cooling or Soft Dry is automatically selected accordingto the indoor temperature.• The operation mode changes every hour, whennecessary.OperationCoolingSoft DryStandardtemperature25°C22°CIndoortemperature23°CHOW TO OPERATE■ To start the operation• Press 1.• POWER indicator (green) on the indoor unit will lightup.• To stop, press once more.■ Setting Mode• Press 2 to select:-Cooling ModelAUTO – Automatic OperationCOOL – Cooling OperationDRY – Soft Dry OperationFAN – Air Circulation OperationHeat Pump ModelAUTO – Automatic OperationHEAT – Heating OperationCOOL – Cooling OperationDRY – Soft Dry Operation OperationCoolingSoft DryHeatingStandardtemperature25°C22°C21°CIndoortemperature23°C20°CHeat Pump ModelCOOL – 26°C ~ 28°CDRY – 1°C ~ 2°Clower than theroom temperatureHEAT – 20°C ~ 24°CCooling ModelCOOL – 26°C ~ 28°CDRY – 1°C ~ 2°Clower than theroom temperatureOFFONHEAHEAT DRDRY FANANCOOLCOOLCHECKTEMPAUTUTOAUTUTOFANANAUTUTORESET CLOCKAIR SWINGOFFCANCEL123TIMEROFF/ONPOWERFULAUTO MANUALECONOMYSLEEPONSETFAN SPEEDMODE235 16434CS-A7BKP CU-A7BKP5 / CS-A7BKP CU-A7BKP6 / CS-A9BKP CU-A9BKP5 / CS-A9BKP CU-A9BKP6 / CS-A12BKP CU-A12BKP5 / CS-A12BKP CU-A12BKP6