Panasonic DP-100 Series Instruction Manual
Also see for DP-100 series: Instruction manualInstruction manualInstruction manual
Contents |
INSTRUCTION MANUALHigh-performance Digital Display Pressure SensorDP-100 SeriesME-DP110EPJ No.0040-90VThank you very much for purchasing Panasonic products. Read this Instruction Manu-al carefully and thoroughly for the correct and optimum use of this product. Kindly keepthis manual in a convenient place for quick reference.WARNING Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products whichmeet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-tion applicable in each region or country. This product is designed for use with non-corrosive gas. It cannot be used for liq-uid or corrosive gas. A product intended for use in Japan conforms to the Japanese Measurement Act.Do not use a product intended for use overseas in Japan.1 PART DESCRIPTIONOutput 1 operationindicatorLights up when com-parative output 1 is ONOutput 2 / analoguevoltage / current out-put operation indicatorStandard type:Lights up when com-parative output 2 is ONHigh-function type:Lights up when analoguevoltage / current output is setMode selection keyUnit display(Note 1, 2)Main displaySub displaySetting valueDOWN keySetting value UP keyConnectorareaPressure portG1/8 + M5 female screwNote: If set the pressure unit other than ‘MPa’ or ‘kPa’, attach the unit switching label corresponds to the set pressureunit.2 PIPING When connecting a commercial coupler to the pres-sure port, attach a 14mm spanner to the pressureport’s hexagon section to fix the port, and thentighten with a tightening torque of 9.8N·m or less(M5 female: 1N·m or less). The commercial coupleror pressure port section will be damaged if the tight-ening torque is excessive.Wrap sealing tape around the coupler when con-necting to prevent leaks.14mm spanner3 MOUNTING The sensor mounting bracket MS-DP1-1 is available as an option. When mountingthe sensor onto the sensor mounting bracket, etc., the tightening torque should be0.5N·m or less.M3 (length 6mm) screwswith washers(Accessory with MS-DP1-1)Sensor mounting bracketMS-DP1-1 (Optional) The panel mounting bracket MS-DP1-2 (optional), as well as the front coverMS-DP1-3 (optional) are also available. For mounting of the panel mounting bracket, refer to the Instruction Manual en-closed with MS-DP1-2.4 WIRING Make sure to use the cable with connector when connecting to thisproduct’s connector area. Tighten the M8 connector completely by hand when mounting. (The tighteningtorque: 0.3 to 0.4N·m) If tightened by a tool such as a plier, it may cause connector damage. Connection method Insert the cable with connector (op-tional) into this product’s connector area, and Disconnection method Loosen the fixing ring, and, holding the fixingring, pull to separate the connector.M8 connectorFixing ringNote: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connectorbreak. |
Related manuals for Panasonic DP-100 series
Panasonic DP-100 Series Instruction Manual
Panasonic DP-00 Series Instruction Manual
Panasonic DP-M Series Instruction Manual
Panasonic CY-100 Series Instruction Manual
Panasonic FX-100 Series Instruction Manual
Panasonic CY-100 Series Instruction Manual
Panasonic FX-100-Z Series Instruction Manual
Panasonic EZ-10 Series Instruction Manual
Panasonic EX-10 series Instruction Manual
Panasonic PE Series Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine